745937

Parkside IAN 280251 PEH 30 B2 Manual

12
Zoom out
Zoom in
Previous page
1/53
Next page
12
GB / IE / NI
□
Exert some slight sideways pressure when
guiding the planer with the guide fence.
●
Using the rebate depth stop
(see Fig. J)
□
Attach the rebate depth stop to the
device with the fixing screw .
□
Set the desired rebate depth with the
rebate depth stop .
□
Make the required number of passes with
the planer until desired rebate depth is
achieved.
●
Removing and installing a
planer blade (see Fig. D + E)
DANGER OF INJURY!
Before you carry out any work on the device
always pull the mains plug out of the mains
socket.
■
CAUTION! The sharp cutting edges of
the planer blade present an injury
hazard! Never touch the cutting edges of
the planer blade .
The planer blade has two cutting edges
and it can be fitted either way around.
□
Replace the planer blade when both
cutting edges are blunt.
□
Do not resharpen the planer blades .
Reversing or replacing a planer
blade
IMPORTANT INFORMATION:
Do not release the two hex srews
27
. They
are used to adjust the height of the blade
shaft.
Adjustment is necessary only if you wish
to use a different planer blade type e.g. a
profiled blade.
Always replace both blades at the same time
to avoid out of balance forces.
NOTE: If you only release one blade first
then you can use the factory-fitted second
blade for orientation when you fit the new
blade.
1. Release the three bolts of the cutting element
using the supplied open spanner .
□
Press the removable side guard into
the slot in the housing.
2. Push the cutting element sideways out
from the blade shaft .
3. Push the planer blade sideways out
from the cutting element .
4. Reassembly is carried out in the reverse
order with a reversed or new planer
blade.
5. Planer blades can be obtained from
the service address indicated (see section
about warranty).
●
Replacing a drive belt
(see Figs. F + G)
DANGER OF INJURY!
Before you carry out any work on the device
always pull the mains plug out of the mains
socket.
□
Release the screws and remove the belt
cover
.
□
Remove the worn drive belt .
□
First place the new drive belt on to
the small belt wheel and then pull the
drive belt on to the large belt wheel
by rotating it.
□
Put the belt cover back into position
and fasten it into place with the screws
.
●
Maintenance and cleaning
DANGER OF INJURY!
Before you carry out any work on the device
always pull the mains plug out of the mains
socket.
Preparing for use / Maintenance and cleaning
4
4
5
5
11
12
12
17
18
18
18
20
20
20
20
20
20
20
20
20
21
23
23
23
25
26
24
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 280251 PEH 30 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 280251 PEH 30 B2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info