746143
15
Zoom out
Zoom in
Previous page
1/114
Next page
1 5
NIIEGB
4. Take off the locknut ( 16) and
the adapter ange (
15) from
the spindle ange (
17).
5.
Open the tightening lever ( 19).
6. Place the protective hood
(
14) on the positioning holes.
7. Turn the protective hood (
14)
into the working position. The
closed side of the protective hood
must always face the operator.
8. Close the tightening lever
(
19) again. The protective
hood should not be able to be
turned any more.
9. Install the locknut (
16) and
adapter ange (
15) in rever-
se order.
10. Readjust the position of the pro-
tective hood if you nd during
use that it does not provide opti-
mum protection.
If needed, the tension on the adjustment
nut (
18) can be set. Use the chuck key
(
13) for this.
Installing/changing disc
1. Press the spindle stop button
(
9).
2. Turn the mounting spindle (
17) until the spindle lock xed
the mounting spindle. Keep and
continue to hold down the spind-
le lock button (
9)
3. Release the clamping nut
(
16) with the chuck key
(
13). You can release the
spindle lock button (
9).
4. Set the desired disc onto the
mounting ange (
15). label
on the disc should always face
the device.
5. Set the clamping nut (
16)
on the mounting spindel (
17) again. The at side of the
clamping nut must face the at-
tachment tool.
6. Press the spindle stop button
(
9) and turn the mounting
spindle (
17), until the spindle
toggle button holds the spindle
ange in a xed position. Pull the
clamping nut (
16) tight again
using the chuck key (
13).
You can let go of the spindle lock
button (
9).
Operation
Caution! Risk of injury!
- Always remove the mains plug
before working on the tool.
- Only use grinding discs and acces-
sories recommended by the ma-
nufacturer. Using other attachment
tools and other accessories can
represent a risk of injury for you.
- Only use grinding tools which
bear information about the
manufacturer, type of binding,
dimension and permitted number
of revolutions.
- Only use grinding discs where
the printed rotational speed is at
least as high as what has been
specied on the name plate of
the device.
- Do not use any broken, cracked,
or otherwise damaged grinding
discs.
- Never operate the device wit-
hout protective equipment.
- Support the plates or workpieces
in order to reduce the risk of
kickback from a jammed cutting
disc. Large workpieces may
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 280250 PWS 125 D3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 280250 PWS 125 D3 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info