746143

Parkside IAN 280250 PWS 125 D3 Manual

13
Zoom out
Zoom in
Previous page
1/114
Next page
1 3
NIIEGB
Other special safety instructions
for cutting grinding
a) Avoid blocking the cutting disc or pres-
sing down too hard. Do not make any
excessively deep cuts. Overloading the
cutting disc increases wear and its ten-
dency to tilt or block and, with that, to
kickback or break the grinder.
b) Avoid the area in front of and behind
the rotating cutting disc. When you
move the cutting disc by itself in the
workpiece, in the event that the electric
tool kicks back with the rotating disc, it
can spin directly towards you.
c) If the cutting disc jams, or you interrupt
your work, switch the device off and
hold it until the disc has come to a full
stop. Never try to pull the cutting disc
out of the cut while it is still running,
because it can kick back. Identify and
correct the cause of the jamming.
d) Do not switch the electric tool on again
as long as it is in the workpiece. Allow
the cutting disc to rst reach its full
rotational speed before you carefully
resume with the cutting. Otherwise, the
disc may catch, spring away from the
workpiece or cause a kickback.
e) Support plates or workpieces to reduce
the risk of kickback from a jammed cut-
ting disc. Large workpieces may bend
under their own weight. The workpiece
must be supported on both sides of the
disc, near the cutting disc as well as
also at the edge.
f) Be particularly careful for pocket cuts in
existing walls or other areas where you
cannot see what is there. The cutting
disc may cause a kickback when it cuts
into gas or water lines, electrical lines
or other hidden objects.
Additional safety instructions
for sanding
Special safety instructions for
sanding:
• Do not use overly large sand-
paper sheets; follow the
manufacturer‘s information for
sandpaper sizes. Sandpaper sheets
which extend beyond the sanding plate
can cause injuries and can block, tear
the sandpaper, or cause kickback.
Additional safety instructions
for polishing
Special safety instructions for
polishing:
• Let no loose parts of the poli-
shing bonnet, particularly at-
tachment strings. If you shorten
the fastening cords verse defrost
oder. Loose, revolving attachment
strings can capture your ngers or be-
come entangled in the workpiece.
Additional safety instructions
for working with wire brushes
Special safety instructions for
working with wire brushes:
• Be aware that the wire brushes
also lose wire pieces during typi-
cal use. Do not overload the wi-
res by pressing down too hard.
Flying wire pieces can very easily penet-
rate thin clothing and/or your skin.
• If a protective hood is recom-
mended, do not allow the wire
brushes and the protective hood
to touch each other. The diameter
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 280250 PWS 125 D3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 280250 PWS 125 D3 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info