745549

Parkside IAN 275685 PDMH 4500 A3 Manual

8
Zoom out
Zoom in
Previous page
1/72
Next page
9 GB/IE
General safety instructions for air tools / General safety rules
Disconnect the compressed air unit from the air
supply after each use and when not in use.
Do not use the compressed air unit if it is not air
tight or in need of repair.
Never connect the compressed air unit to an air
hose with pressure exceeding 6.3 bar.
Keep your working area clean and well lit. Untidy
or poorly lit working areas can result in accidents.
Doing so will allow you better control of the
device, particularly under unforeseen circum-
stances.
Only have the equipment
repaired by qualified specialist personnel using
OEM spare parts. This will maintain the safety
of the device.
Keep children and other persons away from the
device during use. Distractions can cause you
to lose control of the device.
Wear suitable clothing. Do not wear loose cloth-
ing or jewellery. Keep your hair, clothing and
gloves clear of moving parts. Loose clothing,
jewellery or long hair can become trapped in
moving parts.
Put down trigger and device in the event of un-
expected compressor failure.
If possible, use a condensate trap or regularly
drain the hoses and pipes of condensate (water)
before and whilst using compressed air units.
ATTENTION! An undersized com-
pressed air system may minimise the
efficiency of your device.
General safety rules
For multiple hazards, read and understand the
safety instructions before installing, operating,
repairing, maintaining, changing accessories
on, or working near the non-rotary percussive
power tool. Failure to do so can result in serious
bodily injury.
Only qualified and trained operators should
install, adjust or use the non-rotary percussive
power tool.
Do not modify this non-rotary percussive power
tool. Modifications can reduce the
effectiveness of safety measures and increase
the risks to the operator.
Do not discard the safety instructions; give them
to the operator.
Do not use the non-rotary percussive power tool
if it has been damaged.
Tools shall be inspected periodically to verify
the ratings and markings required by this part
of ISO 11148 are legibly marked on the tool.
The employer / user shall contact the manufac-
turer to obtain replacement marking labels when
necessary.
Never modify the product. Modifications reduce
the effectiveness of safety measures and increase
the risk of injuries.
Never use a damaged device.
Use and maintain the device as recommended
in the instructions for use to minimise dust or gas-
ses, noise and vibration.
Do not use the device in idle to prevent the chisel
from ejecting uncontrolled.
Use the consumables and the inserted tool as
specified in the instructions for use to minimise
dust or gasses, noise and vibration.
Regularly maintain the device to verify all re-
quired rated values and markings such as rated
speed or rated air pressure, required by ISO
11148, are legible on the device. If necessary,
the user must contact the manufacturer for re-
placement labels for markings.
Risks due to projected parts
Disconnect the non-rotary percussive power tool
from the energy source when changing inserted
tool or accessories.
Be aware that failure of the workpiece, or ac-
cessories, or even of the inserted tool itself can
generate highvelocity projectiles.
Always wear impact-resistant eye protection dur-
ing the operation of the non-rotary percussive
power tool. The grade of protection required
should be assessed for each use.
For overhead work, wear a safety helmet.
The risks to others should also be assessed at
this time.
General safety instructions for air tools
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 275685 PDMH 4500 A3 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 275685 PDMH 4500 A3 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info