Manual Parkside IAN 275685 PDMH 4500 A3 (page 10 of 72) (English, German, Dutch, Danish, French)

745549

Zoom out

Zoom in

1/72

11 GB/IE

General safety rules

Stop using the device if you experience numb-

ness, tingling, pain or lightening of the skin of

the ﬁngers or hands, and consult a physician.

Risks associated with accessories

Disconnect the non-rotary percussive power tool

from the energy supply before changing the in-

serted tool or accessory.

Use only sizes and types of accessories and

consumables that are recommended by the

non-rotary percussive power tool manufacturer;

do not use other types or sizes of accessories

and consumables.

For hammers, where appropriate, never use any

chisel as a hand-struck tool. They are speciﬁcally

designed and heat-treated for use only in non-

rotary percussive power tools.

For hammers and breakers, where appropriate,

never use blunt chisels, as they require exces-

sive pressure and can break from fatigue. Blunt

tool-pieces can increase vibration and, therefore,

sharp tools should always be used.

For hammers, where appropriate, never cool a

hot accessory in water. Brittleness and early

failure can result.

For hammers, where appropriate, chisel break-

age or tool damage can result from misuse of

using the tool as a lever, e.g. prising. Take smal

ler

“bites” to avoid getting stuck.

Avoid direct contact with the inserted tool during

and after use, as it can be hot or sharp.

ATTENTION! Disconnect the device from the

air supply before performing maintenance or

cleaning.

Only use the manufacturer recommended sizes

and types of accessories and consumables.

Do not use the chisel as a hand-held tool. They

were developed speciﬁcally for use with the a

chipper.

Only use sharp chisels, as dull chisels require

more pressure and could break as well as increas

vibration.

Do not cool hot tools in water. Doing so may

result in damage.

Do not use the chisels as hand-held tools.

Never use the chisel whilst or after operating the

device. The ﬁngers or hands could be injured.

The chisel can get very hot.

Do not use defective devices. Replace defective

parts to prevent injuries.

Hazards in the work

environment

Slips, trips and falls are major causes of work-

place injury. Be aware of slippery surfaces

caused by use of the tool and also of trip haz-

ards caused by the air line or hydraulic hose.

Proceed with care in unfamiliar surroundings.

Hidden hazards, such as electricity or other

utility lines, can exist.

The non-rotary percussive power tool is not in-

tended for use in potentially explosive atmos-

pheres and is not insulated against coming into

contact with electric power.

Make sure there are no electrical cables, gas

pipes, etc., that can cause a hazard if damaged

by use of the tool.

Slipping, tripping and falling are the main causes

of injuries at the workplace. Be aware of slippery

areas caused by use of the device, as well as

tripping hazards caused by the air hose.

Beware of hidden hazards such as electric cables,

or gas- and water lines.

This device is not insulated against electric shock.

Avoid any contact with electric cables. This device

is not suitable for use in explosive environments.

This device is not suitable for use in explosive

areas: using this device can produce sparks.

Therefore never use this device near combustible

materials, ﬂuids or gasses.

Hazards due to dust and vapours

Dust and fumes generated when using non-ro-

tary percussive power tools can cause ill health

(for example cancer, birth defects, asthma and /

or dermatitis); risk assessment and implementa-

tion of appropriate controls for these hazards

are essential.

General safety rules

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 275685 PDMH 4500 A3 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 1,36 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 275685 PDMH 4500 A3 Manual

Product: