Manual Parkside IAN 275679 PDEXS 150 B2 (page 12 of 66) (English, German, Dutch, Danish, French)

745526

Zoom out

Zoom in

1/66

PDEXS 150 B2

Operation

Switching on and oﬀ

Switching on:

♦ First press the locking mechanism forwards and

then the trigger

to switch the appliance on.

Switching oﬀ:

♦ Let go of the trigger

♦ When you have ﬁnished working, disconnect

the appliance from the compressed air source.

Regulation of vibration output

■

Use the speed controller

to control the air-

ﬂow and thus the vibration output (also during

operation).

■

The ideal speed depends on the material being

worked and can be determined through practical

tests.

Use the pressure reducer to set the correct working

pressure.

Sanding

♦ Switch on the compressed air source and allow

it to run until the maximum tank pressure has

been reached.

♦ Use the pressure reducer on the compressed

air source to set the optimum working pressure.

Note that the maximum working pressure may

not be exceeded. An excessive working pres-

sure does not mean increased output; it merely

increases the air consumption and accelerates

appliance wear. Always comply with the techni-

cal information.

♦ Switch on the compressed air-powered random

orbital sander.

♦ Allow the device to reach the required speed

and adjust as necessary.

♦ Guide the compressed air-powered random

orbital sander parallel onto the workpiece.

♦ Move the appliance parallel and in ﬂat circles

or alternatively lengthwise and across the sur-

face. Use the housing

as a handle to guide

the appliance in the desired direction.

♦ Do not press the compressed air-powered ran-

dom orbital sander down. Pressing down hard

does not increase the working eﬃciency!

♦ When you have ﬁnished working, let go of the

trigger

to switch oﬀ the appliance.

♦ When you have ﬁnished working, disconnect

the appliance from the compressed air source.

CAUTION!

► Sanding creates dust. Always wear protective

gloves, a suitable mask and clean the sand-

paper and workpiece at regular intervals with

a vacuum cleaner or compressed air.

► Suitable safety precautions must be taken

depending on the size and nature of the

workpiece. Use suitable clamping devices to

prevent the workpiece from slipping.

► In the event of an interruption to the air sup-

ply, release the trigger

immediately.

Working procedures

The most important thing to remember when sand-

ing is to use successively ﬁner grained paper.

With a coarse grain, the surface will not become

smooth, but rather rougher. If the grain is too ﬁne,

you will hardly achieve any noticeable result.

The material removal rate is determined by the

speed and grain size of the sandpaper.

The sandpaper used should be appropriate to the

substance being worked and the amount of mate-

rial to be removed.

CAUTION!

► Ensure that the appliance is disconnected

from the compressed air source before you ﬁt

or remove a sandpaper disc

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 275679 PDEXS 150 B2 in the language / languages: English, German, Dutch, Danish, French as an attachment in your email.

The manual is 0,6 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 275679 PDEXS 150 B2 Manual

Product: