745330

Parkside IAN 273280 PFBS 160 A1 Manual

45
Zoom out
Zoom in
Previous page
1/50
Next page
45 GB
Start-up
First slide the tool you wish to use through the
clamping nut
6
before inserting it into the
collet
7
,
26
fitting the tool shaft.
Press and hold the spindle lock
9
.
Insert the collet
7
,
26
into the threaded insert,
then tighten the clamping nut
6
using the
combination wrench
25
on the thread.
Using a tool with clamping mandrel:
Use the screwdriver end of the combination
wrench
25
to loosen and tighten the screw on
the clamping mandrels.
Insert the clamping mandrel in the tool as de-
scribed.
Using the combination wrench
25
, loosen the
screw on the clamping mandrel.
Insert the attachment you wish to use onto the
screw between two washers.
Use the combination wrench
25
to tighten the
screw on the clamping mandrel.
Brick
Do not resharpen any edges by hand with
the brick
21
.
Installing sanding belts
Slide the grinding belt
23
onto the grinding man-
drel
24
from the top. Tighten the screw on the grind-
ing mandrel
24
to secure the grinding belt
23
.
Attaching polishing tools
Turn the polishing attachment
22
on the point
of the mandrel for polishing attachments
32
.
Switching on and off /
Adjusting the speed
Switching on / adjusting the speed:
Set the ON / OFF switch
1
to position „I“ by
pressing down and sliding it forward.
Set the variable speed control
11
to a position
between „1“ and „MAX“.
Switching off:
Set the ON / OFF switch
1
to position „0“.
Using the grip collar with LED light
Hold the spindle lock
9
and unscrew the
clamping nut
6
from the thread, turning coun-
ter-clockwise.
Release the spindle lock
9
.
Then screw the union nut
5
anti-clockwise from
the thread.
Screw the grip collar with LED light
8
onto the
thread, turning clockwise.
Hold the spindle lock
9
and screw the clamp-
ing nut
6
onto the thread, turning clockwise.
Release the spindle lock
9
.
Set the ON / OFF switch of the LED light
36
to
position “I“ to switch it on (see Fig. C).
Set the ON / OFF switch of the LED light
36
to
position “0“ to switch it off again.
Repeat the steps in reverse order to reattach the
union nut
5
.
Information about processing
materials / tool / speed range
Use the router bits to process wood, plastic and
sheetrock at maximum speed.
Determine the speed range for processing zinc,
zinc alloys, aluminium, copper and lead by
testing scrap pieces.
Process plastics and materials with a low melt-
ing point at a low speed.
Process wood at high speeds.
Clean, polish and buff at a medium speed.
Note: The milling bit
31
is not intended for use on
steel or iron. Suitable milling bits are available.
The following information are non-binding recom-
mendations. When performing the actual work also
test yourself, which tools and settings are ideal for
the material you are working on.
General power tool safety warnings / Start-up
… 45 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 273280 PFBS 160 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273280 PFBS 160 A1 in the language / languages: French as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 273280 PFBS 160 A1

Parkside IAN 273280 PFBS 160 A1 User Manual - English, German, Dutch, Danish, French - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info