Manual Parkside IAN 273280 PFBS 160 A1 (page 43 of 50) (French)

745330

Zoom out

Zoom in

1/50

43 GB

General power tool safety warnings

Additional safety instructions

for grinding and cutting-oﬀ

operations

Safety warnings specific for grinding and

abrasive cutting-off operations:

a) Use only wheel types that are recom-

mended for your power tool and only

for recommended applications.

For example: do not grind with the

side of a cut-off wheel. Abrasive cut-off

wheels are intended for peripheral grinding,

side forces applied to these wheels may cause

them to shatter.

b) For threaded abrasive cones and plugs

use only undamaged wheel mandrels

with an unrelieved shoulder flange that

are of correct size and length. Proper

man-

drels will reduce the possibility of breakage.

c) Do not “jam” a cut-off wheel or apply

excessive pressure. Do not attempt to

make an excessive depth of cut. Over-

stressing the wheel increases the loading and

susceptibility to twisting or snagging of the wheel

in the cut and the possibility of kickback or w

heel

breakage.

d) Do not position your hand in line with

and behind the rotating wheel. When

the wheel, at the point of operation, is moving

away from your hand, the possible kickback m

propel the spinning wheel and the power tool

directly at you.

e) When wheel is pinched, snagged or

when interrupting a cut for any reason,

switch off the power tool and hold the

power tool motionless until the wheel

comes to a complete stop. Never att

empt

to remove the cut-off wheel from the

cut while the wheel is in motion other-

wise kickback may occur. Investigate and

take corrective action to eliminate the cause of

wheel pinching or snagging.

f) Do not restart the cutting operation in

the workpiece. Let the wheel reach full

speed and carefully re-enter the cut.

The wheel may bind, walk up or kickback if

the power tool is restarted in the workpiece.

g) Support panels or any oversized work-

piece to minimize the risk of wheel

pinching and kickback. Large workpieces

tend to sag under their own weight. Supports

must be placed under the workpiece near the

line of cut and near the edge of the workpiece

on both sides of the wheel.

h) Use extra caution when making a

“pocket cut” into existing walls or

other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring

or objects that can cause kickback.

Additional safety instructions

for wire brushing operations

Safety warnings specific for wire brushing

operations:

a) Be aware that wire bristles are thrown

by the brush even during ordinary op-

eration. Do not overstress the wires

by applying excessive load to the

brush.

The wire bristles can easily penetrate light cloth-

ing and / or skin.

Allow brushes to run at operating spe

for at least one minute before using

them. During this time no one is to

stand

in front or in line with the brush. Loose

bristles or wires will be discharged during the

run-in time.

c) D

irect the discharge of the spinning wir

brush away from you. Small particles and

tiny wire fragments may be discharged at high

velocity during the use of these brushes and

may become imbedded in your skin.

Safety notices speciﬁc to

rotary tools

When you use the drill / grinder wear the fol-

lowing protective equipment: safety glasses and

protective gloves.

CAUTION! RISK OF INJURY! The tool

continues to rotate after it has been switched

oﬀ! Avoid contact with rapidly rotating drill /

grinder components.

General power tool safety warnings

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273280 PFBS 160 A1 in the language / languages: French as an attachment in your email.

The manual is 1,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 273280 PFBS 160 A1

Parkside IAN 273280 PFBS 160 A1 User Manual - English, German, Dutch, Danish, French - 80 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 273280 PFBS 160 A1 Manual

Product: