Manual Parkside IAN 273280 PFBS 160 A1 (page 42 of 50) (French)

745330

Zoom out

Zoom in

1/50

42 GB

General power tool safety warningsGeneral power tool safety warnings

workpiece allows you to use your hand(s) to

control the tool. Round material such as dowel

rods, pipes or tubing have a tendency to roll

while being cut, and may cause the bit to bind

or jump toward you.

m) Position the cord clear of the spinning

accessory. If you lose control, the cord may

be cut or snagged and your hand or arm may

be pulled into the spinning accessory.

n) Never lay the power tool down until

the accessory has come to a complete

stop. The spinning accessory may grab the

surface and pull the power tool out of your control.

o) After changing the bits or making any

adjustments, make sure the collet nut,

chuck or any other adjustment devices

are securely tightened. Loose adjustment

devices can unexpectedly shift, causing loss of

control, loose rotating components will be vio-

lently thrown.

p) Do not run the power tool while car-

rying it at your side. Accidental contact

with the spinning accessory could snag your

clothing, pulling the accessory into your body.

q) Regularly clean the power tool’s air

vents. The motor’s fan will draw the dust inside

the housing and excessive accumulation of pow-

dered metal may cause electrical hazards.

r) Do not operate the power tool near

flammable materials. Sparks could ignite

these materials.

s) Do not use accessories that require

liquid coolants. Using water or other liquid

coolants may result in electrocution or shock.

Further safety instructions

for all operations

Kickback and related warnings

Kickback is a sudden reaction to a pinched or sn

agged

rotating wheel, sanding band, brush or any other

accessory. Pinching or snagging causes rapid stalling

of the rotating accessory which in turn causes the

uncontrolled power tool to be forced in the direction

opposite of the accessory’s rotation.

For example, if an abrasive wheel is snagged or

pinched by the workpiece, the edge of the wheel

that is entering into the pinch point can dig into the

surface of the material causing the wheel to climb

out or kick out. The wheel may either jump toward

or away from the operator, depending on direction

of the wheel’s movement at the point of pinching.

Abrasive wheels may also break under these con-

ditions.

Kickback is the result of power tool misuse and / or

incorrect operating procedures or conditions and

can be avoided by taking proper precautions as

given below.

a) Maintain a firm grip on the power tool

and position your body and arm to al-

low you to resist kickback forces. The

operator can control kickback forces, if proper

precautions are taken.

b) U

se special care when working corne

rs,

sharp edges etc. Avoid bouncing and

snagging the accessory. Corners, sharp

edges or bouncing have a tendency to snag the

rotating accessory and cause loss of control or

kickback.

Do not attach a toothed saw blade. S

uch

blades create frequent kickback and loss of

control.

d) Always feed the bit into the material

in the same direction as the cutting

edge is exiting from the material

(which

is the same direction as the chips are

thrown). Feeding the tool in the wrong direc-

tion causes the cutting edge of the bit to climb

out of the work and pull the tool in the direction

of this feed.

e) When using rotary files, cut-off wheels,

high-speed cutters or tungsten carbide

cutters, always have the work securely

clamped. These wheels will grab if they be-

come slightly canted in the groove, and can

kickback. When a cut-off wheel grabs, the

wheel itself usually breaks. When a rotary file,

high-speed cutter or tungsten carbide cutter

grabs, it may jump from the groove and you

could lose control of the tool.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273280 PFBS 160 A1 in the language / languages: French as an attachment in your email.

The manual is 1,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 273280 PFBS 160 A1

Parkside IAN 273280 PFBS 160 A1 User Manual - English, German, Dutch, Danish, French - 80 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 273280 PFBS 160 A1 Manual

Product: