745330

Parkside IAN 273280 PFBS 160 A1 Manual

47
Zoom out
Zoom in
Previous page
1/50
Next page
47 GB
Start-up
Store accessories inside the original box or oth-
erwise protect the accessories from damage.
Store accessories dry and away from aggres-
sive media.
Tips and tricks
Applying excessive pressure can cause the in-
stalled tool to break and / or damage the work
piece. Optimal results can be achieved by ap-
plying the tool to the work piece at a steady
speed range and little pressure.
Hold the device with both hands whilst cutting.
Please note the data and information in the
chart to prevent the spindle end touching the
perforated plate of the grinding tool.
Flexible shaft
Never use the spindle lock with the motor on.
The tool or the flexible shaft could otherwise
be damaged.
Unscrew the union nut
5
from the tool, turning
counter-clockwise, and put aside.
Press and hold the spindle lock
9
.
Unscrew the clamping nut
6
from the tool,
turning counter-clockwise.
Attach the flexible shaft
14
to the tool, inserting
the inner axle on the flexible shaft along with
the clamping nut
6
into the collet
7
,
26
.
Use the combination wrench
25
to first tighten t
he
clamping nut
6
, then the union nut
14 b
of the
flexible shaft
14
to the tool, turning clockwise.
Now insert the accessory you wish to use into
the collet
7
,
26
of the flexible shaft.
To lock the spindle, slide back the black sleeve
on the flexible shaft.
Using the combination wrench
25
, open the
collet holder
15
on the flexible shaft, insert the
accessory and tighten the collet holder
15
.
Stretch stand for the
multi-function tool (Fig. J)
Screw the stretch stand
17
into the clamp
18
.
Note: The stretch stand
17
can be screwed
into the clamp in two different positions, de-
pending on the whether you‘re attaching to a
horizontal or vertical surface.
Secure the clamp
18
at the edge of a work-
bench or a work table no thicker than 55 mm.
The stretch stand
17
is height adjustable. Loosen
the upper tube of the stretch stand
17
by turning
to the left (–). Extend the tube to the maximum
height and secure by turning to the right (+).
The holder
16
is also height adjustable, simple
turn the black thread to the left. After adjusting
the holder to the correct height, turn the thread
in the opposite direction to tighten.
Secure the tool to the holder
16
of the stretch
stand
17
with the metal bracket
3
. This hold-
er
16
rotates by 360°.
Base assembly
Using the attachment, the tool is particularly suited
for cutting special shapes (holes for sockets, etc.).
Attach the milling bit
31
as described in chapter
„Attaching / changing the tool / collet“.
Ensure that the bit’s shaft protrudes from collet
by approx. 13 mm.
Unscrew the union nut
5
from the tool, turning
clockwise, and put aside.
Screw the base
13
onto the unit.
To set the correct working depth, loosen the
locking screw
12
and adjust the bottom of the
base assembly to the desired size.
Then tighten the locking screw
12
.
Start-up
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 273280 PFBS 160 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 273280 PFBS 160 A1 in the language / languages: French as an attachment in your email.

The manual is 1,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 273280 PFBS 160 A1

Parkside IAN 273280 PFBS 160 A1 User Manual - English, German, Dutch, Danish, French - 80 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info