745345

Parkside IAN 270414 PTBM 500 B2 Manual

12
Zoom out
Zoom in
Previous page
1/76
Next page
12
GB IE
Recommended speeds for
different drill sizes and materials:
Ø [mm]: Ø [mm]:
[1/min]:
6 - 8 9 - 10
> 8 > 10
< 3 < 4
3 - 4 5 - 6
5 7 - 8
Checking the V-belt
1. Release the locking bolt (11) on the
gear cover (8).
2. Open the gear cover (8).
3. Check the tension of the V-belt (26).
4. The V-belt (26) is correctly tensioned
when it gives way slightly when
pressed.
5. Check the V-belt (26) for tears, cuts or
other damage.
6. Close the gear cover (8). Fasten the
locking bolt (11) on the gear cover (8).
Tensioning the V-belt
1. Release the locking bolt on the gear
cover (8).
2. Open the gear cover (8).
3. Release the retaining bolt (13) on the
motor unit (14).
4. Slide the motor unit (14) back to tensi-
on the V-belt (26).
5. The V-belt (26) is correctly tensioned
when it gives way slightly when
pressed.
6. Tighten the retaining bolt (13) on the
motor unit (14) again.
7. Close the gear cover (8). Fasten the
locking bolt (11) on the gear cover (8).
Adjusting the Drilling Bench
1. Release the locking handle (24).
2. Push the drilling bench (20) to the desi-
red height.
3. Pivot the drilling bench (20) to the desi-
red position.
4. Fasten the drilling bench (20) again
with the locking handle (24).
5. You can also adjust the tilt angle of the
drilling bench (20). To do this, release
the retaining screw (19) under the
drilling bench. Tilt the drilling bench
(20) as desired to the right or left up to
a max. of 45° and secure the drilling
bench (20) again with the retaining
screw (19).
Preselecting the Drilling Depth
1. Move the red arrow to the „0“ position
on the drilling depth scale (3).
2. Turn one of the drill lifting arms (9) an-
ticlockwise and move the spindle (6) to
the desired drilling depth.
3. Screw the stop nut onto the desired
point on the depth scale. Tighten the
xing nut against the stop nut. Read off
the red arrow on the drilling depth sca-
le to help you.
4. Move the spindle (6) slowly back to the
stop position.
5. Adjust the drilling bench (20) until the
workpiece is resting against the drill tip.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 270414 PTBM 500 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 270414 PTBM 500 B2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info