745345

Parkside IAN 270414 PTBM 500 B2 Manual

14
Zoom out
Zoom in
Previous page
1/76
Next page
14
GB IE
Clamping the Workpieces
Only work with workpieces that can be
securely clamped. The workpiece must not
yield too much. Otherwise it is nor possib-
le to apply adequate tension.
The workpiece must not be too small or too
large either.
Removing Blockages
- You should always select a suitable
feed rate which allows trouble-free chip
breaking.
- If the bit is jammed in the workpiece,
turn off the power and unplug the po-
wer cord. Turn the bit on the drill chuck
anticlockwise with a little jerk to break
the chip and release the bit again.
- If a fragment is produced during the
processing of the workpiece, turn off
the power and unplug the power cord.
Use a pair of pliers and remove the
fragment to prevent it ying off in an
uncontrolled way.
Cleaning and Servicing
Pull the mains plug before any ad-
justments, maintenance or repair.
Have any work on the device
that is not described in this in-
struction guide performed by
a professional. Only use ori-
ginal parts. Allow the device
to cool off before any mainte-
nance or cleaning is underta-
ken. There is a risk of burning!
Always check the device before using it
for obvious defects such as loose, worn or
damaged parts, correct the positioning of
screws or other parts. Exchange the dama-
ged parts.
Cleaning
Do not use any cleaning agents or
solvents. Chemical substances can
etch the plastic parts of the device.
Never clean the device under run-
ning water.
• Thoroughly clean the device after every
use.
• Clean the ventilation openings and the
surface of the device with a soft brush
or cloth.
• Remove chips, dust and dirt with a va-
cuum cleaner if necessary.
• Lubricate moving parts regularly.
• Do not allow lubricants to come into
contact with switches, V-belts, pulleys
and drill lifting arms.
Storage
• Store the appliance in a dry place well
out of reach of children.
• The device can be relocated over a
short distance with two people. Reloca-
ting the device over a longer distance
generally has to take place with a trans-
port aid.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 270414 PTBM 500 B2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 270414 PTBM 500 B2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info