745222
15
Zoom out
Zoom in
Previous page
1/60
Next page
15
GB IE
The grinding disc nut must not be
screwed too tightly in order to
avoid a breaking of the grinding
disc and nut.
8. Test run:
Before starting work and after each
change of grinding disc, carry out a
test run of at least 60 seconds with no
load. Switch off the equipment immedi-
ately if the disc runs lumpy, substantial
vibrations occur, or abnormal noises
are generated.
Change wet grinding disc
1. Loosen the 3 xing screws
(13a/13b/13c) and remove the
water tank (13).
2. Unscrew the grinding disc nut (22)
with a screw wrench (SW19) and
hold against the grinding disc
(
1)with one hand wearing a
glove. Unscrew the nut (right-hand
thread):
turn counter-clockwise.
3. Remove the washer (26) with a
plastic clamping ange (27) and
the grinding disc (
1).
4. Fit on the new grinding disc (1)
and the plastic clamping ange
(27) with the washer and screw
the grinding disc nut (22) manu-
ally onto the right-side nut (right-
hand thread):
turn clockwise.
The two plastic clamping anges
(27/28) are not identical.
5. Tighten the grinding disc nut with
a screw wrench (SW19) applying
modest manual force.
6. Push the water tank back over the
wet grinding disc and onto the
gear unit housing (29).
7. Fasten the water tank (
13)
back on the gear unit housing
(29) using the three screws.
The grinding disc nut must not be
screwed too tightly in order to
avoid a breaking of the grinding
disc and nut.
8. Test run:
Before starting work and after each
change of grinding disc, carry out a
test run of at least 60 seconds with no
load. Switch off the equipment immedi-
ately if the disc runs lumpy, substantial
vibrations occur, or abnormal noises
are generated.
Cleaning and
maintenance
Disconnect the plug before adjust-
ment, maintenance or repair.
Have any work not described
in these instructions carried
out by a specialist workshop.
Use only original components.
Allow the equipment to cool
before carrying out any main-
tenance and cleaning work.
There is a risk of burns.
Cleaning
Do not use cleaning agents or sol-
vents. Chemical substances may
attack plastic parts of the equipment.
Never clean the equipment under
running water.
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Parkside IAN 115727 PNTS 250 A1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 115727 PNTS 250 A1 in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 4,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Parkside IAN 115727 PNTS 250 A1

Parkside IAN 115727 PNTS 250 A1 User Manual - French - 56 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info