Manual Parkside IAN 113362 PMGS 12 C3 (page 13 of 91) (English, German, Dutch, French, Swedish)

745224

Zoom out

Zoom in

1/91

13 GB/IE

General safety advice for electrical power tools / Operation

Wear a dust mask!

NOXIOUS FUMES!

Ensure that there is adequate ventilation when

machining surfaces containing plastic or cov-

ered with paint, varnish etc.

Do not soak the materials or the sur-

face you are about to work on with

liquids containing solvents.

Avoid abrading paints containing lead

or other substances hazardous to

health.

Do not machine materials containing

asbestos. Asbestos is a known carcinogen.

Do not machine moist materials or

damp surfaces.

NOTE! Do not allow the tool to come to a

standstill by overloading it!

Switch the device off

and allow it to come to a standstill be-

fore you put it down.

Always keep the de

vice

clean, dry and free of oil or grease.

This device is not intended to be used by per-

sons (including children) with impaired physi-

cal, sensory or mental capacity or lacking the

experience and / or knowledge. Always super-

vise children to ensure they do not play with

the tool.

If the external connection wire / cable(s)

for this transformer is / are damaged, it / they

must be replaced by the manufacturer or its cus-

tomer service, or a similarly qualiﬁed person to

avoid hazards.

Safety isolating transformer

fail-safe

Fusible cut-out

Operation

Never use the device for a purpose

for which it was not intended or with

non-original parts / accessories. The use

of tools or accessories other than those recom-

mended in the operating instructions could lead

to you suﬀering an injury.

Changing the battery

ATTENTION!

Do not leave drained battery in the device, as

even leak-proof batteries can corrode, releasing

chemicals which could be harmful to your health

or ruin the device.

Do not leave batteries lying about carelessly.

Children or pets could swallow them. If acciden-

tally swallowed seek immediate medical attention

Remove the batteries from the device when it

will not be used for extended periods to prevent

leaks.

Touching leaked or damaged batteries may

cause chemical burns. Therefore wear suitable

protective gloves in this event.

Ensure batteries are not short-circuited. Never

throw batteries into ﬁre.

Do not recharge batteries. Explosion hazard!

Ensure the LED light is switched oﬀ. Remove the

three battery cover screws at the back of the

grip collar with LED

Remove the drained battery and replace with a

new battery (button cell LR41). Please note the

correct polarity when inserting the batteries.

Close the battery compartment by fastening the

three screws.

Inserting or replacing

a tool / collet

Press the spindle lock

and keep it pressed.

Rotate the clamping nut

until the lock

engages.

Loosen the clamping nut

with the combina-

tion key

If a tool is already inserted, remove it.

First insert the tool you wish to use through the

clamping nut

before you insert it into the

collet

suitable for the tool shaft.

Press the spindle lock

and keep it pressed.

Insert the collet

into the threaded insert and

tighten the clamping nut

on the thread using

the combination key

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Parkside IAN 113362 PMGS 12 C3 in the language / languages: English, German, Dutch, French, Swedish as an attachment in your email.

The manual is 1,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Parkside IAN 113362 PMGS 12 C3 Manual

Product: