458602

Paradyne FrameSaver NP 110 Manual

73
Zoom out
Zoom in
Previous page
1/175
Next page
5 Diagnostics
5-6 NetPath 110 User’s Manual - Installation Guide 980-001-0240B
November
2000
User Ckt Status - Displays current status being detected by CSU.
States (in highest priority order) are:
RTS:State of RTS lead, when Power is being detected from the DTE.
States are: ON or OFF.
DTR:State of DTR lead, when Power is being detected from the DTE.
States are: ON or OFF.
LL: State of LL lead, when Power is detected from the DTE.
States are: ON or OFF.
Pwr: ON or OFF based on sensing voltage on Tx data lead(s) from the DTE.
Frame Fault - Displays (blank) or the highest priority Fault causing a disruption of the
data path.
Refer to the Appendix in this manual for a list and description of all fault
displays.
Commands:
ResetTest [RT] - Resets BERT or PVC result counters without disrupting the test
operation and refreshes all dynamic information contained on the screen.
InjectErr [IE secs] - Injects a single bit error into the BERT stream. When issued
without the “secs,” a single bit error will be injected at execution of this command.
When issued with a “secs” value between 1 - 255, a single bit error will be injected
once a second for the number of “secs” entered (user can issue other commands while
this takes place in background).
RebootExt [RE secs] - Used to interrupt AC Power to the DTE device connected to
the Switched AC Output connector on the rear of the unit, thereby forcing the de-
vice to reboot. When issued with a “secs” parameter, power will remain off for the
specified length of time (1 - 300 seconds). When issued as “RE” only, power will
be interrupted for five seconds at the execution of this command.
Help [?] - Advances to “Help” for Device Status / Test screen.
Close [X] - Returns to System View screen.
AutoUpdate [AU] - Provides automatic screen update and refresh (every five sec-
onds) of all status and Test (when active) results. No changes can be made while in this
mode, and the bottom lines on the screen are replaced as shown in Figure 5-4. AutoUp-
date is exited by pressing ENTER.
Fi
g
ure 5-4 Auto Update Screen Chan
g
e
---> Screen updates every 5 seconds <---
---> Press Enter for Command Prompt <---
… 73 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paradyne FrameSaver NP 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paradyne FrameSaver NP 110 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info