458602

Paradyne FrameSaver NP 110 Manual

72
Zoom out
Zoom in
Previous page
1/175
Next page
5 Diagnostics
980-001-0240B FrameSaver NP 110 User’s Manual - Installation Guide 5-5
November 2000
Table 5-2 Test Modes
Network User Description
Clear Clear Terminates operator or externally-initiated Loopbacks,
BERT, and Test Packet tests.
Line Lp to Netw Sets a Line Loopback at the T1 interface toward the
Network.
Payld Lp to Netw Sets a Payload Loopback in the CSU toward the Network.
User Lp to Netw Loops the User Port back toward the Network.
Send LoopUp
or
Send LoopDn
Transmits T1 Line Loop Up or Line Loop Down code
toward the Network.
QRSS to Netw
Alt Ones to Netw
2047 to Netw
Zero to Netw
Directs the indicated Full T1 BERT Pattern toward the
Network.
User 2047 to Netw
User Zero to Netw
Directs the indicated BERT Pattern toward the Network
Circuit (for DS0s assigned to the User Port.)
Loop to User Loops data back to User Port.
2047 to User Directs the indicated BERT Pattern toward the User Circuit.
Line Lp to CPE Full T1 Line Loopback applied within the unit’s framer
toward the CPE port(s): User Port (also DSX Port and Drop
Port if DSX/Drop Adapter installed.)
Test Pkts to New Sends Link Test Packets (40 -1590 octets) toward the
Network (T1 Facility).
NOTES:
1. All User Port Loops and BERTs are at the current User Port configured data rate (56 or 64 kBps.)
2. Only one BERT may be active at a time. The results are a count of the number of Blocks Sent,
Blocks Errored, Block Error Rate and the duration of the test, displayed as shown on the example
screen above. When the BERT duration reaches the maximum count of 99:59:59, all counts freeze
until cleared or reset by the operator (the BERT data however, continues to be sent).
3. PVC tests will prompt for the input of a PVC DLCI destination.
4. Test Pkts to Netw display results include selected DLCI, packets sent, packets dropped, percent
received, octets sent, test duration and average and maximum delay (network and full delay), for
each network segment.This test’s delay values may not correlate to values displayed on the PVC
Statistics Screens because the Link Test Packet size (40 - 1590 octets) is larger than the Delay
measurement packet (36 octets).
5. Delay and Loss measurement packets (for ALL
PVCs) are halted, while a “Test Pkts to Netw” test is
performed. This will also affect the Delay and Loss packet counts and measurement fields on the
PVC Statistics Screens.
6. Initiating certain test options, when management access is via the T1 link, will terminate
management. These tests will be blocked and an Error Message displayed on the screen. Examples
of this are “BERT to Netw” and “Test Pkts to Netw” where the DLCI selection matches the
management DLCI of this unit.
… 72 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paradyne FrameSaver NP 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paradyne FrameSaver NP 110 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info