458602

Paradyne FrameSaver NP 110 Manual

67
Zoom out
Zoom in
Previous page
1/175
Next page
4 Operation
4-26 FrameSaver NP 110 User’s Manual - Installation Guide 980-001-0240B
November
2000
Test
Installation
The final step of the FrameSaver NP 110 installation is to verify operations. This is
done through the Network Control Center (NCC).
1. Contact the Network Control Center and inform the Operator that the physical
installation and initial configuration are completed.
2. The NCC will establish a management session to the FrameSaver NP 110 and
complete any final/additional configuration, and review the system’s status screens
to verify operation.
NOTE: To enable NCC management access, the local console session must be logged
out, and if the NCC is attempting a dial-in connection, the local terminal must also be
disconnected from the AUX 2 port.
If this installation is configured for Out-Of-Band Trap Reporting, a test of this feature
should also be performed. This is done by initiating a Network communications failure
which causes the FrameSaver NP 110 to issue a Trap Report to the Trap Manager. This
test must be coordinated with the NCC Operator to verify that the Trap Report is re-
ceived and that Network communications are restored after the test.
3. Coordinate the initiation of this test with the NCC Operator, and when told to do
so, disconnect the T1 Line from the FrameSaver NP 110. The FrameSaver NP 110
will dial-out to issue a Trap Report after approximately five (5) seconds. This can
be seen on the front panel by the “MODEM IN USE” LED going steady ON. After
the “MODEM IN USE” LED goes OFF, reconnect the T1 Line and confirm with
the NCC Operator that the Trap Report has been received, and that good
communications have been reestablished with the FrameSaver NP 110.
NOTE: If the NCC management session (Step # 2) was established via dial-in, this
must be terminated before the FrameSaver NP 110 can use the Modem to issue the
Trap Report.
This dial-out Trap Report test is highly recommended because it adds a greater level
of confidence to the completion of the installation process. This test verifies all of the
following, in addition to the normal operation of the FrameSaver NP 110:
•
Dial Line is operational and a call can be made (not inadvertently blocked).
•
Trap Manager phone number is correct.
•
IP Address is correct.
•
Trap Manager Address and Community are correct.
The installation and initial testing are now complete. If any results were other than
those described, refer to section 5, “Diagnostics” in this manual for assistance.
… 67 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paradyne FrameSaver NP 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paradyne FrameSaver NP 110 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info