458602

Paradyne FrameSaver NP 110 Manual

56
Zoom out
Zoom in
Previous page
1/175
Next page
4 Operation
980-001-0240B FrameSaver NP 110 User’s Manual - Installation Guide 4-15
November
2000
T391/Status Enquiry Rate - Interval in seconds between the LMI Status
Enquiries issued by the FrameSaver NP 110 to the Network (Frame Switch).
The ratio of N392 to N393 defines the rate of Bad/No LMI responses to Count of
events, beyond which the Network link is declared Out-of-Service. This ratio is
set by selecting the values (1 to 10) for each of these parameters, defined as
follows:
N392/Event Error Threshold - Number of Bad/No responses to LMI Status
Enquiries issued by FrameSaver NP 110.
N393/Event Count - Count of all monitored requests (to be used for the ratio).
N391/Full Status Frequency - The Frequency Number “n” will cause every
“n
th
” LMI Status Enquiry issued to be a Full LMI Status Enquiry.
PVC BECN/FECN Threshold - FrameSaver NP 110 maintains a count of
seconds during which a receive frame contained a BECN or FECN bit set. When
the number of seconds containing BECN or FECN bits (flags) for any PVC in the
most recent interval equals or exceeds this Threshold Setting, an alarm is
declared.
5. User (DCE) - Consists of the settings required for the various protocols. These
include T392, N392 and N393.
T392/Status Enquiry Timeout - Timeout interval in seconds while waiting for
an LMI Status Enquiry from the User equipment.
The ratio of N392 to N393 defines the rate of Bad/No LMI inquiries to Count of
events, beyond which the User link is declared Out-of-Service. This ratio is set
by selecting the values (1 to 10) for each of these parameters, defined as
follows:
N392/Event Error Threshold - Number of Bad/No inquiries for LMI Status
Enquiries issued by the User equipment.
N393/Event Count - Count of all monitored inquiries (to be used for the ratio).
Force Full Status Response - Enable causes the FrameSaver NP 110 to send
four consecutive Full LMI Enquiry Messages toward the Network upon detecting
a recovery of its T1 link (or ISDN link if so optioned and active). Upon receiving
a Full Response it forwards that to the DTE, regardless of that enquiry type. In
some cases this will speed recovery from a link outage. Disable causes the
FrameSaver NP 110 to follow normal conventions per the N391 parameter.
6. Link Err Threshold - Disable or set the threshold of Data Frame Error Seconds
which when reached or exceeded causes an alarm to be declared. Set
independently for Network and User sides.
Commands:
Help [?] - Advances to “Help” for Frame Manager Configuration screen.
Save [SA] - Saves parameters and returns to System View screen.
Cancel [X] - Returns to System View screen without saving changes.
Save the Frame Manager Configuration changes when they are all set correctly by en-
tering “SA” followed by ENTER. Also returns the user to the System View screen.
Proceed to SNMP Community Access Configuration, selecting [SC] by typing
“SC” followed by ENTER.
… 56 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paradyne FrameSaver NP 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paradyne FrameSaver NP 110 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info