458602

Paradyne FrameSaver NP 110 Manual

53
Zoom out
Zoom in
Previous page
1/175
Next page
4 Operation
4-12 FrameSaver NP 110 User’s Manual - Installation Guide 980-001-0240B
November
2000
CSU / Interface
Configuration
The CSU / Interface Configuration screen allows you to view and alter parameters for
the CSU and CPE interface operations.
Figure 4-4 shows the CSU / Interface Configuration screen.
Fi
g
ure 4-4 CSU / Interface Confi
g
uration Screen
1. Name - Device’s ID as defined in unit’s Device Configuration.
2. Page - Shows the page number of the displayed page. When the DSX/Drop
option adapter module is present, page 2 may be selected to configure settings for
the option module. Refer to section 6 “Options” of this manual for DSX/Drop
settings.
DS0 Assignments - Shows the assignment of the DS0s (time-slots) to the unit's User
Port with an "X" in the DS0s column location.
3. User - Defines which DS0s will be allocated to the User port.
All the DS0s for a port are entered with a single command. The DS0 numbers may
be entered: separately with a "comma" between each number, as a range with a
"dash" between the start and end numbers, or a combination of both formats. For
example, any of the following commands will result in DS0s 1 through 8 being
assigned to the User Port.
U=1,2,3,4,5,6,7,8 or U=1-8 or U=1,2,3,4-8
Entering a blank for a port command will clear all assignments for that port.
************************* CSU / Interface Configuration ************************
Name: F@43802
Page [P=#]: 1 of 1
----------- DSO Assignments ---------- ------- Network Port Settings ------
111111111122222
123456789012345678901234 Facility ID [I=]: NONAME
User [U=]: XXXXXXXXXXXXXXXXXXXXXXXX
Build Out [B1=] Framing [T1=]
>>1) T1-0<< >>1) ANSI<<
2) T1-7 2) AT&T
([U=m,n,..r] and/or [U=m-n] for multiples) 3) T1-15 3) SF
4) T1-22
--------- User Port Settings ---------- Clock Source [S=]
Ones Dens [D1=] >>1) Network<<
Data Rate: 1536 Kbs >>1) B8ZS<< 2) Internal
2) AMI
DS0 Format [F1=] Port TxD Clk [C1=]
1) Nx56 kbs >>1) DCE<< Link Err Thres [L1=#]: Disabled
>>2) Nx64 kbs<< 2) DTE X to Disable or 1 thru 895 seconds
Help[?] Save[SA] Cancel[X]
>
… 53 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Paradyne FrameSaver NP 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Paradyne FrameSaver NP 110 in the language / languages: English as an attachment in your email.

The manual is 1,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info