424269
63
Zoom out
Zoom in
Previous page
1/86
Next page
8. Options
61
8 OptionsMulti - Units
8.1 Operating additional
units
Additional handsets: Additional handsets are
available for purchase (page 11). Up to 6
handsets can be registered to a single base unit.
Using additional handsets allows you to have an
intercom call while simultaneously conducting a
call to an outside line.
L Additional handsets have answering device
controls printed on their cases, however,
remote operation of the base unit’s
answering device is not possible.
Additional base units: You can register and
operate your handset with up to 4 base units.
Each base unit forms 1 radio cell. If the individual
base units are linked to the same telephone line
then you can extend the operating range of the
system by positioning the base units so that the
two radio cells overlap. If the handset is set to
AUTO” in base unit selection (page 62), then in
standby mode the handset will automatically
swap to the second base if the range on the first
base is exceeded. It is not possible to transfer
calls between base units (only between
handsets linked to the same base unit).
Example: Additional handsets registered to 2
base units.
Note:
L Calls are disconnected when the handset
moves from one radio cell to another.
8.2 Registering a handset
to a base unit
The handset supplied with the base unit is
already registered. If an optional handset is
purchased, it must be registered.
L Keep the front cover page open for button
locations.
Important:
L After pressing {LOCATOR/HOLD} in step
8, the rest of the procedures must be
completed within 1 minute.
L Charge the optional handset batteries for
7 hours before initial use.
To exit programming, press {ih} any time.
1 Press {j}.
2 Press {e} or {v} repeatedly to display
SETTING HS”.
3 Press {>}.
4 Press {e} or {v} repeatedly to display
REGISTRATION”.
5 Press {>}.
6 Press {e} or {v} repeatedly to display
REGISTER HS”.
7 Press {>}.
8 Press and hold {LOCATOR/HOLD} on the
base unit until the registration tone sounds.
L It may take up to about 10 seconds until
the registration tone sounds.
L REGISTRATION” will be displayed on
the base unit.
L If all registered handsets start ringing
(paging), press {LOCATOR/HOLD} to
stop paging then start over again.
9 Using the handset, press {e} or {v}
repeatedly to select the desired base unit
number available to register the handset,
and press {>}.
10 After “BS PIN” is displayed, enter the 4-digit
base unit PIN, using the handset dial keypad.
L The default PIN is “0000”.
11 Press {>} or {j}.
L When a handset is registered
successfully, a confirmation tone will
sound and w will light.
8.2.1 Cancelling a handset
Each handset can cancel itself or another
handset.
1 Press {j}.
2 Press {e} or {v} repeatedly to display
SETTING BS”.
3 Press {>}.
L INPUT CODE” will be displayed.
Radio cell
1
2
3
5
4
chapter8 Page 61 Thursday, March 6, 2003 1:54 PM
63


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic kx fc 195 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic kx fc 195 in the language / languages: English as an attachment in your email.

The manual is 7,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info