602952

Panasonic DMPBD10A Manual

26
Zoom out
Zoom in
Previous page
1/32
Next page
RQT8966
26
Operation Page
Displays
TV screen and video
(Continued on the next page)
Cannot operate the television. ≥Change the manufacturer code. Some televisions cannot be operated even if you change the
code.
≥It may be necessary to set the manufacturer code again after changing the batteries.
11
11
The remote control doesn’t
work properly.
≥The remote control and main unit are using different codes. Change the code on the remote
control.
Press and hold [ENTER] and the indicated number button at the same
time for more than 2 seconds.
≥The batteries are depleted. Replace them with new ones.
≥You are not pointing the remote control at the main unit’s remote control signal sensor during
operation.
≥Coloured glass may obstruct the signal reception/transmission.
≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
≥It may be necessary to set the code on the remote control again after changing the batteries.
11
7
7
—
—
11
The unit is on but cannot be
operated.
≥Some operations may be prohibited by the disc.
≥The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.
≥One of the unit’s safety devices may have been activated.
Reset the unit as follows:
1 Press [Í/I] on the main unit to switch the unit to standby.
If the unit doesn’t switch to standby, press and hold [Í/I] on the main unit for about 10
seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains lead, wait one minute, then reconnect it.
2 Press [Í/I] on the main unit to switch it on. If the unit still cannot be operated, consult the
dealer.
≥Condensation has formed: Wait 1 to 2 hours for it to evaporate.
—
28
—
—
Play fails to start even when
[1] (PLAY) is pressed.
Play starts but then stops
immediately.
≥Insert the disc correctly with the label facing up.
≥The disc is dirty.
≥You tried to play a blank disc or unplayable disc on this unit.
12
2
4, 5
The Video CD picture does not
display properly.
≥When connecting to multi-system TV, select “NTSC” in “TV System” in the Setup menu.
≥When connecting to PAL TV, the lower part of the picture cannot be displayed correctly
during search.
23
—
Time Slip does not work. ≥Time Slip does not work when the unit’s “TV System” settings are different from the title
recorded on the disc.
23
Cannot eject disc. ≥The unit may have a problem. While the unit is off, press and hold [;] and [5/9] on the
main unit at the same time for about 5 seconds. Remove the disc and consult the dealer.
—
Startup is slow.
When the unit is turned on,
audio and video output takes a
long time.
≥Startup takes time in the following situations.
–Immediately after a power failure or the AC mains lead is connected.
–When the unit is connected with an HDMI cable.
—
D
R
The display is dim. ≥Change “FL Display” in the “Display” tab of the Setup menu. 22
The elapsed time displayed is
actually less than the playtime.
≥The displayed play time is converted from the number of frames at 29.97 frames (equal to
0.999 seconds) to one second. There will be a slight difference between the time displayed
and the actual elapsed time (e.g., actual one-hour elapsed time may display as
approximately 59 minutes 56 seconds).
—
The images from this unit do
not appear on the television.
Picture is distorted.
The television may display
incorrectly or colours appear
faded.
≥Make sure that the television is connected to the AV terminal, VIDEO OUT terminal, S
VIDEO OUT terminal, COMPONENT VIDEO OUT terminals or HDMI AV OUT terminal on
this unit.
≥Make sure that the television’s input setting (e.g., AV 1) is correct.
≥Progressive output is set to on but the connected television is not progressive compatible.
While stopped, press and hold [∫] and [1] (PLAY) on the main unit at the same time for
more than 5 seconds to cancel this setting. The setting will change to interlace.
≥Set “Transfer” in Picture menu to “Auto”.
≥The unit and television are using different video systems. While stopped, keep pressing [∫]
and [< OPEN/CLOSE] on the main unit for 5 or more seconds. The system switches from
PAL t o
NTSC
or vice versa.
≥The system used on the disc doesn’t match your television.
–
PAL discs cannot be correctly viewed on an NTSC television.
–This unit can convert NTSC signals to PAL60 for viewing on a PAL television (“TV System” in
the “Connection” tab).
–]BD-V] This unit cannot convert BD-Video from NTSC signals to PAL60 signals; therefore
video cannot be displayed properly when you connect this unit to the AV terminal, VIDEO
terminal or S VIDEO terminal.
8, 9
—
—
20
—
23
Video is not output in high
definition.
≥High definition video cannot be output through the AV, VIDEO OUT or S VIDEO OUT
terminals.
≥Depending on the BD-Video, output from the COMPONENT VIDEO OUT terminals may be
restricted to 576p/480p.
—
—
RGB video is not output from
the AV terminal.
≥When connecting to an amplifier/receiver with an HDMI cable, set “HDMI Video Mode” in the
“
HDMI
” tab to “Off”.
23
Status messages do not appear.
≥Select “Automatic” in “On-Screen Messages” of the “Display” tab in the Setup menu. 22
The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.
≥Use the television to change the aspect. Refer to your television’s operating instructions.
≥If connecting with a component video cable, set “Progressive” to “Off” in the Picture menu. If
this doesn’t help or you cannot set it to “Off”, then set the “TV Aspect” of the “Connection” tab
to “4:3 Pan & Scan” in the Setup menu.
—
20, 22
Reference 11 Troubleshooting guide
DMP-BD10A.book Page 26 Thursday, March 15, 2007 7:45 PM
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Panasonic DMPBD10A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Panasonic DMPBD10A in the language / languages: English as an attachment in your email.

The manual is 6,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Panasonic DMPBD10A

Panasonic DMPBD10A User Manual - German - 96 pages

Panasonic DMPBD10A User Manual - Dutch, Danish - 108 pages

Panasonic DMPBD10A User Manual - French, Italian - 96 pages

Panasonic DMPBD10A User Manual - Swedish, Spanish - 108 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info