796577

Oregon Scientific THGN301 Manual

4
Zoom out
Zoom in
Previous page
1/80
Next page
EN
4
1. Prepare a pole, a plastic mount bracket and a U-bolt
without flat washers, lock washers and hex nuts
(figure 1).
2. Position the pole inside the U-bolt and securely
tighten the mount bracket on the pole with the U-bolt
by the four pairs of the flat washers, lock washers
and hex nuts (figure 2). Use wrench if necessary.
NOTE
Make sure the engraved arrow UP on the mount
bracket is positioned correctly.
3. Insert the extended tabs of the mount bracket into
the slots on the back of the transmitter box. Push
the transmitter box down until it is securely in place
(figure 3 & 4).
NOTE
Locate the transmitter box in direct sunlight for
optimal power supply to the solar panel (see Sensor
Installation section).
Option 2: Install the transmitter box on a
wooden board
UP
UP
UP
12
34
1. Prepare a wooden board, a plastic mount bracket
and four pairs of Type A screws without flat
washers and lock washers (see above figure 1).
2. Position the mount bracket on the wooden board by
securely tightening the Type A screws using some
tools (see above figure 2).
NOTE
Make sure the engraved arrow UP on the mount
bracket is positioned correctly.
3. Insert the extended tabs of the mount bracket into
the slots on the back of the transmitter box. Push
the transmitter box down until it is securely in place
(see above figure 3 & 4).
NOTE
Locate the transmitter box in direct sunlight for
optimal power supply to the solar panel (see Sensor
Installation section).
SET UP THERMO & HYGRO SENSOR
The thermo & hygro sensor takes outdoor temperature
and humidity readings. Before positioning the sensor,
install the sensor onto a metal mount bracket.
• Securely tighten the sensor on the metal mount
bracket by Type B screws with lock washers and
flat washers. Use wrench if necessary (figure 7).
Option 1: Install the sensor on a pole
1. Prepare a pole and a U-bolt without flat washers,
lock washers and hex nuts. Position the pole inside
the U-bolt (figure 8).
2. Securely tighten the metal mount bracket on the
pole with the U-bolt by the four pairs of the flat
washers, lock washers and hex nuts (figure 9).
3. Securely locate the pole in your desired outdoor area.
Option 2: Install the sensor on a wooden board
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oregon Scientific THGN301 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oregon Scientific THGN301 in the language / languages: English, German, Dutch, French, Italian, Portuguese, Swedish, Spanish as an attachment in your email.

The manual is 23.95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info