63833
119
Zoom out
Zoom in
Previous page
1/124
Next page
119
Troubleshooting—Continued
If your TV is connected to the HDMI OUT, set the
“Monitor Out” setting to “HDMI” (page 41), and
select “- - - - -” in the “HDMI Input Setup” on page 44
to watch composite video, S-Video, and component
video sources.
If your TV is connected to the COMPONENT VIDEO
MONITOR OUT, set the “Monitor Out” setting to
“Analog” (page 41), and select “- - - - -” in the “Com-
ponent Video Setup” on page 45 to watch composite
video and S-Video sources.
If the video source is connected to a component video
input, you must assign that input to an input selector
(page 45), and your TV must be connected to either
the HDMI OUT or COMPONENT VIDEO MONI-
TOR OUT (page 25 and 34).
If the video source is connected to an HDMI input,
you must assign that input to an input selector
(page 44), and your TV must be connected to the
HDMI OUT (page 34).
While the Pure Audio listening mode is selected, the
video circuitry is turned off and only video signals
input through HDMI IN can be output.
On your TV, make sure that the video input to which
the AV receiver/AV amplifier is connected is selected.
There’s no picture from a source connected to
an HDMI IN
Reliable operation with an HDMI-to-DVI adapter is
not guaranteed. In addition, video signals from a PC
are not supported (page 34).
When the “Monitor Out” is set to “Analog” (page 41),
and the “Output Resolution” (page 94) is set to any
resolution not supported by the TV, no video is output
by the HDMI OUT.
The onscreen menus don’t appear
If your TV is connected to the analog outputs, set the
“Monitor Out” setting to “Analog” (page 41).
On non-North American models, specify the TV sys-
tem used in your area in the “TV Format Setup” on
page 48.
On your TV, make sure that the video input to which
the AV receiver/AV amplifier is connected is selected.
The picture is distorted
On non-North American models, specify the TV sys-
tem used in your area in the “TV Format Setup” on
page 48.
The immediate display does not appear
The immediate display will not appear when the input
signal from the COMPONENT VIDEO IN is output to
a device connected to the COMPONENT VIDEO
MONITOR OUT.
Depending on the input signal, the immediate display
may not appear when the input signal from the HDMI
IN is output to a device connected to the HDMI OUT.
Reception is noisy, FM stereo reception is
noisy, or the FM STEREO indicator doesn’t
appear
Relocate your antenna.
Move the AV receiver away from your TV or com-
puter.
Listen to the station in mono (page 59).
When listening to an AM station, operating the remote
controller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
The remote controller doesn’t work
Make sure that the batteries are installed with the cor-
rect polarity (page 14).
Install new batteries. Don’t mix different types of bat-
teries, or old and new batteries (page 14).
Make sure that the remote controller is not too far
away from the AV receiver/AV amplifier, and that
there’s no obstruction between the remote controller
and the AV receiver/AV amplifier’s remote control
sensor (page 14).
Make sure that the AV receiver/AV amplifier is not
subjected to direct sunshine or inverter-type fluores-
cent lights. Relocate if necessary.
If the AV receiver/AV amplifier is installed in a rack or
cabinet with colored-glass doors, the remote controller
may not work reliably when the doors are closed.
Make sure you’ve selected the correct remote control-
ler mode (pages 15 and 107-113).
When using the remote controller to control other
manufacturers’ AV components, some buttons may
not work as expected.
Make sure you’ve entered the correct remote control code.
Make sure to set the same ID on both the AV receiver/
AV amplifier and remote controller (page 93).
Can’t control other components
If it’s an Onkyo component, make sure that the u
cable and analog audio cable are connected properly.
Connecting only an u cable won’t work (page 39).
Make sure you’ve selected the correct remote control-
ler mode (pages 15 and 107-113).
If you’ve connected an u-capable Onkyo MD
recorder, CD recorder, RI Dock to the TAPE IN/OUT
jacks, or an RI Dock to the GAME/TV IN jacks, for
the remote controller to work properly, you must set
the display to MD, CDR, or DOCK (page 50).
If you cannot operate it, you will need to enter the
appropriate remote control code (page 105).
To control another manufacturer’s component, point
the remote controller at that component.
Tuner (TX-SR806 only)
Remote Controller
TX-SR806_En.book Page 119 Monday, August 4, 2008 10:25 AM
119


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR806 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR806 in the language / languages: English as an attachment in your email.

The manual is 9,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR806

Onkyo TX-SR806 User Manual - German - 242 pages

Onkyo TX-SR806 User Manual - Dutch - 242 pages

Onkyo TX-SR806 User Manual - Italian - 242 pages

Onkyo TX-SR806 User Manual - Swedish - 242 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info