63833
120
Zoom out
Zoom in
Previous page
1/124
Next page
120
Troubleshooting—Continued
To control an Onkyo component that’s connected via
u, point the remote controller at the AV receiver/AV
amplifier. Be sure to enter the appropriate remote con-
trol code first (page 106).
To control an Onkyo component that’s not connected
via u, or another manufacturer’s component, point
the remote controller at the component. Be sure to
enter the appropriate remote control code first
(page 105).
The entered remote control code may not be correct. If
more than one code is listed, try each one.
If none of the codes work, use the Learning function
to learn the commands of the other component’s
remote controller (page 114).
Can’t learn commands from another remote
controller
When learning commands, make sure that the trans-
mitting ends of both remote controllers are pointing at
each other.
Are you trying to learn from a remote controller that
cannot be used for learning? Some commands cannot
be learned, especially those that contain several
instructions.
Can’t record
On your recorder, make sure the correct input is
selected.
When the Pure Audio listening mode is selected,
recording is not possible because no video signals are
output. Select another listening mode.
There’s no sound
Only components connected to analog inputs can be
played in Zone 2.
The sound changes when I connect my
headphones
When a pair of headphones is connected, the listening
mode is set to Stereo, unless it’s already set to Stereo,
Mono, Direct, or Pure Audio.
The display doesn’t work
The display is turned off when the Pure Audio listen-
ing mode is selected.
How do I change the language of a multiplex
source
Use the “Multiplex” setting on the “Audio Adjust”
menu to select “Main” or “Sub” (page 83).
The u functions don’t work
To use u, you must make an u connection and an
analog audio connection (RCA) between the compo-
nent and AV receiver/AV amplifier, even if they are
connected digitally (page 39).
The functions Auto Power On/Standby and
Direct Change don’t work for components
connected via u
These functions don’t work when Zone 2 is turned on.
When performing “Automatic Speaker Setup”,
the measurement fails showing the message
“Ambient noise is too high”.
This can be caused by any malfunction in your speaker
unit. Check if the unit produces normal sounds.
The following settings can be made for the S-
Video and composite video inputs
You must use the buttons on the unit to make these set-
tings.
1. While holding down the input selector button for the
input source that you want to set, press the [SETUP]
button.
2. Use the Left and Right [e]/[r] buttons to change
the setting.
3. Press the [SETUP] button when you’ve finished.
•Video Attenuation
This setting can be made for the DVD, VCR/DVR,
CBL/SAT, GAME/TV, or AUX input.
If you have a games console connected to the
S-Video or composite video input, and the picture
isn’t very clear, you can attenuate the gain.
Video ATT:OFF: (default).
Video ATT:ON: Gain is reduced by 2 dB.
Recording
Zone 2
Others
The AV receiver/AV amplifier contains a microcomputer
for signal processing and control functions. In very rare
situations, severe interference, noise from an external
source, or static electricity may cause it to lockup. In the
unlikely event that this happens, unplug the power cord
from the wall outlet, wait at least five seconds, and then
plug it back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit’s malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
For North American models, set the AV receiver to
Standby before disconnecting the power cord from the
wall outlet. For other models, set the AV receiver/AV
amplifier to Standby and the POWER switch to OFF
before disconnecting the power cord.
TX-SR806_En.book Page 120 Monday, August 4, 2008 10:25 AM
120


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-SR806 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-SR806 in the language / languages: English as an attachment in your email.

The manual is 9,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-SR806

Onkyo TX-SR806 User Manual - German - 242 pages

Onkyo TX-SR806 User Manual - Dutch - 242 pages

Onkyo TX-SR806 User Manual - Italian - 242 pages

Onkyo TX-SR806 User Manual - Swedish - 242 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info