517568
65
Zoom out
Zoom in
Previous page
1/160
Next page
Advanced Operations
En-65
Operating
procedure
( page 61)
Speaker Impedance
` 4ohms:
Select if the impedance of any speaker is
4 ohms or more but less than 6.
` 6ohms
:
Select if the impedances of all speakers are
between 6 and 16 ohms.
Speakers Type(Front)
` Normal
:
Select this if you’ve connected your front
speakers normally.
` Bi-Amp:
Select this if you’ve bi-amped your front
speakers.
` Digital Crossover:
Select this if you’re using speakers without
crossover network.
Tip
If “Speakers Type(Front)” is set to “Digital Crossover”, a
confirmation screen appears. Select “Next (2-7. Digital
Processing Crossover Network)” to display the screen
for Digital Processing Crossover Network ( page 68).
Continue with the settings.
Powered Zone 2, Powered Zone 3
` No
` Yes:
Zone 2/3 speakers can be used (Powered
Zone 2/3 enabled).
11ch Playback
` No
` Yes
For 11.1-channel playback, set this setting toYes”. If
you select front wide speakers setting in Speaker
Configuration is set to “None”, it will be automatically
switched to “80Hz (THX)”.
Note
Powered Zone 3 is not available in the following cases:
The “Speakers Type(Front)” setting is set to “Bi-Amp” or
Digital Crossover”.
The “Powered Zone 2” setting is set to No”.
When the “Powered Zone 3” setting is set to “Yes” while
Powered Zone 2 is enabled ( page 84), the surround
back speakers cannot be used.
When the “Powered Zone 2” setting is set to “Yes”, the
front wide speakers cannot be used.
When the “Powered Zone 3” setting is set to “Yes”, the
front high speakers cannot be used.
•“11ch Playback” is not available in the following cases:
The “Speakers Type(Front)” setting is set to “Bi-Amp” or
Digital Crossover”.
The “Powered Zone 2” setting is set to Yes”.
The “Zone 2 Monitor Out” setting is set to “Use”.
If the “11ch Playback” setting is set to “Yes”, the audio of
front wide channel is output from FRONT WIDE PRE OUT
only.
Speaker Configuration
With these settings, you can specify which speakers
are connected and a crossover frequency for each
speaker. Specify “Full Band” for speakers that can
output low frequency bass sounds adequately, for
example, speakers with a good sized woofer. For
smaller speakers, specify a crossover frequency.
Sounds below the crossover frequency will be output
by the subwoofer instead of the speaker. Refer to
your speaker’s manuals to determine the optimum
crossover frequencies. If you set up your speakers
using Audyssey MultEQ XT32 Room Correction and
Speaker Setup, please make sure manually that any
THX speakers are set to “80Hz(THX)” crossover.
Subwoofer
` Yes
` No
Front
` Full Band
` 40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz,
200Hz
Note
If the “Subwoofer” setting is set to “No”, the “Front” setting
is fixed at “Full Band”.
Center
*1
, Surround
*1
` Full Band
` 40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz,
200Hz
` None
Front Wide
*1*2*4*6*7
, Front High
*1*2*5*6
` Full Band
` 40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
` None
Surround Back
*2*3*8*9
` Full Band
` 40Hz to 80Hz(THX)
to 100Hz, 120Hz, 150Hz,
200Hz
` None
Note
*1
Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2
If the “Surround” setting is set to “None”, this setting
cannot be selected.
*3
If the “Surround” setting is set to anything other than
Full Band”, “Full Band” cannot be selected here.
*4
When the “Powered Zone 2” setting is set to “Yes”, this
setting cannot be selected.
*5
When the “Powered Zone 3” setting is set to “Yes”, this
setting cannot be selected.
This setting is set automatically by
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup function ( page 28).
65


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR929 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR929 in the language / languages: English as an attachment in your email.

The manual is 4,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR929

Onkyo TX-NR929 Quick start guide - English - 4 pages

Onkyo TX-NR929 Quick start guide - German - 4 pages

Onkyo TX-NR929 User Manual - German - 160 pages

Onkyo TX-NR929 Quick start guide - Dutch - 4 pages

Onkyo TX-NR929 User Manual - Dutch - 160 pages

Onkyo TX-NR929 User Manual - French - 160 pages

Onkyo TX-NR929 User Manual - French - 4 pages

Onkyo TX-NR929 User Manual - Italian - 156 pages

Onkyo TX-NR929 Quick start guide - Italian - 4 pages

Onkyo TX-NR929 User Manual - Swedish - 160 pages

Onkyo TX-NR929 Quick start guide - Swedish - 4 pages

Onkyo TX-NR929 User Manual - Spanish - 160 pages

Onkyo TX-NR929 Quick start guide - Spanish - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info