553769
88
Zoom out
Zoom in
Previous page
1/97
Next page
88
Using the Macro Function
What is the macro function?
A macro function enables you to program a series of
button operations (up to 16) on the remote controller
into a single button. The series of operations are then
called a macro. For example, to play a compact disc
player connected to the TX-NR801/TX-NR801E nor-
mally, you must perform the following steps:
1. Press the RCVR MODE button.
2. Press the ON button.
3. Press the CD (INPUT SELECTOR) button.
4. Press the CD MODE button.
5. Press the playback ( ) button.
By using the macro function, you can perform the above
five operations by only pressing one button.
Tips:
If you erase or change the command of a button pro-
grammed in the macro, that operation of that button
will no longer work in the macro. In this case, it will
be necessary for you to reprogram the macro in order
to avoid incorrect operation.
The codes programmed into the macro will be trans-
mitted at an interval of 0.5 seconds. However, some
devices may not be able to complete one operation in
0.5 seconds and may miss the next code. In this case,
after pressing one operation button, you can press the
same MODE button again before pressing the next
operation button to add another 0.5 seconds between
the two operations.
With the macro function, you can program a series of
button operations as a macro into the MACRO button so
the macro can be executed with just one touch. Note
that for the macro function, only two macros can be
programmed. For example, to program the macro
described above on this page for the MACRO button,
perform the steps given below.
Notes:
You may program up to 16 button operations into the
macro function. If you try to program a 17th opera-
tion, it will be ignored, and programming is stopped.
If the SEND/LEARN indicator quickly flashes three
times and turns off, then the remote controller has
exited the programming mode because either you
have made a mistake during programming or a time-
out has occurred because no button was pressed.
Resume from Step 1.
ON
MACRO 2
MACRO 1
CD MODE
RCVR MODE
MODE buttons
SEND/LEARN
indicator
(CD playback)
CD
(INPUT
SELECTOR)
Programming the Macro
1
Press and hold down any one of the 8
MODE buttons, press the MACRO 1 (or 2)
button, and then release both buttons.
When you press the MODE button, it lights and
the SEND/LEARN indicator lights. When you
press the MACRO 1 (or 2) button, the indicator
turns off. When you release the buttons, the indi-
cator flashes briefly and then lights again.
2
Press the operation buttons you wish to
program in order (in this case, press
RCVR MODE ON CD (INPUT SELEC-
TOR) CD MODE playback ( ) but-
ton).
When you press each button, the SEND/LEARN
indicator turns off. When you release the button,
the indicator lights.
3
Press the MACRO 1 (or 2) button to com-
plete the procedure.
The SEND/LEARN indicator slowly flashes
twice.
4
Check to see if the macro has been prop-
erly programmed.
88


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR801 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR801 in the language / languages: English as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info