553769
89
Zoom out
Zoom in
Previous page
1/97
Next page
89
Using the Macro Function—Continued
Perform the procedure below to execute the macro that
you have programmed into the remote controller. After
programming the macro, you should always run it at
least once to make sure that it has been programmed
properly.
Erasing a macro from the MACRO 1 (or 2) button
Notes:
If the SEND/LEARN indicator quickly flashes three
times and turns off, then the remote controller has
exited the erasing mode because either you have
made a mistake during erasing or a time-out has
occurred because no button was pressed. Resume
from Step 1.
If you press a button other than MACRO 1 (or 2) but-
ton in Step 2, then you will in effect be overwriting
the previous macro with a new macro.
Erasing all commands and macros that have
been programmed
This procedure will erase all the commands and macros
that you have programmed into the remote controller
and return it to its default settings. This operation will
not affect the preset settings of the remote controller.
All programmed commands and macros are erased and
the remote controller returns to its factory presets.
Notes:
Proceed to Step 3 immediately after Step 2; other-
wise, the batteries will be consumed quickly.
If you press any button other than the ENTER/ZONE
2 button in Step 3, nothing will be erased. In this
case, resume from Step 1.
Macro mode programming memo
Executing the Macro
1
Point the remote controller at the
TX-NR801/TX-NR801E.
2
Press the MACRO 1 (or 2) button.
It may take a while for the macro to finish trans-
mitting, so be sure to continue pointing the
remote controller at the device until the SEND/
LEARN indicator turns off.
1
Press and hold down any one of the 8
MODE buttons, press the MACRO 1 (or 2)
button, and then release both buttons.
When you press the MODE button, it lights and
the SEND/LEARN indicator lights. When you
press the MACRO 1 (or 2) button, the indicator
turns off. When you release the buttons, the indi-
cator flashes once.
2
Press the MACRO 1 (or 2) button again.
The SEND/LEARN indicator slowly flashes
twice. The macro programmed to the MACRO
button is erased.
1
Open the battery cover and remove the
batteries from the remote controller.
2
While pressing and holding down the ON
and STANDBY buttons, re-insert the bat-
teries in their correct orientation, and then
release both buttons.
The SEND/LEARN indicator flashes slowly.
3
Press the ENTER/ZONE 2 button.
The SEND/LEARN indicator lights up for about
ten seconds and then turns off.
MACRO 1 MACRO 2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
89


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR801 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR801 in the language / languages: English as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info