553769

Onkyo TX-NR801 Manual

86
Zoom out
Zoom in
Previous page
1/97
Next page
86
Letting the Remote Controller Learn the Codes
from Other Remote Controllers
When programming the commands of another remote
controller to the RC-511M remote controller, you must
first decide under to which MODE button you want the
commands to be linked. In general, you will select the
MODE button that corresponds to the component you are
programming. For example, if you are programming the
functions from a remote controller for a compact disc
player, you would choose the CD MODE button. Then,
by pressing the CD MODE button, the buttons on the RC-
511M remote controller will change to the commands
you program here to operate the compact disc player.
After programming which MODE button to use, you
will then transfer the separate commands from the other
remote controller over to the RC-511M remote control-
ler one at a time. Each command is then programmed to
a different button on the RC-511M remote controller.
Any button is programmable for this step except for the
eight MODE buttons (RCVR, CD, DVD, SAT/MD,
NET A, TV, VCR, and CABLE), the two MACRO but-
tons (1 and 2), and the LIGHT button.
Even after the commands have been memorized, keep
your old remote controller in a safe place. If for some rea-
son the commands are lost (e.g., when the batteries run
down), it will be necessary to memorize them once again.
Programming Procedure
1
Place the remote controller and the
remote controller for the other device fac-
ing each other at a distance of 2 to 6
inches (5 to 15 cm) apart.
ENTER/ZONE 2
MODE buttons
SEND/LEARN
indicator
P
O
W
E
R
S
L
E
E
P
D
IM
M
E
R
S
U
R
M
O
D
E
V
ID
E
O
-1
V
ID
E
O
-2
T
A
P
E
D
V
D
C
D
C
D
D
V
D
T
U
N
E
R
T
U
N
E
R
P
H
O
N
O
IN
P
U
T
S
E
L
E
C
T
O
R
D
IS
C
O
L
U
M
E
C
H
S
E
L
P
R
E
S
E
T
T
E
S
T
T
O
N
E
M
U
L
T
I
-
C
H
I
N
P
U
T
G
R
O
U
P
2 to 6 inches
(5 to 15 cm)
2
While pressing and holding down the
desired MODE button on the remote con-
troller, press the ENTER/ZONE 2 button
and then release both buttons.
The SEND/LEARN indicator lights when the
MODE button is pressed and turns off when the
ENTER button is pressed. When the indicator
turns off, release both buttons. The SEND/
LEARN indicator lights again.
3
Press and release the button on the
remote controller to which you want to
transfer the next command.
You may select any button excluding the eleven
ones indicated in the figure below. When you
press the button, the SEND/LEARN indicator
turns off. When you release the button, the indica-
tor lights again.
If you press the wrong button by mistake, press
that same button again. The SEND/LEARN indi-
cator flashes twice, and the remote controller
exits the programming mode.
4
Press and hold down the button (that cor-
responds to the command you are pro-
gramming) on the remote controller of the
other device until the SEND/LEARN lamp
on the remote controller flashes twice.
After flashing twice, the SEND/LEARN indica-
tor will light again.
5
Repeat Steps 3 and 4 to transfer all the
commands you desire from the other
remote controller and program them to
buttons on the remote controller under
the same MODE.
Repeat Steps 2 through 4 to program commands
to a different MODE (e.g., when programming
from a different remote controller).
6
Press the MODE button that you pressed
in step 2 to complete the programming.
7
Operate the newly programmed buttons to
make sure the learning function was per-
formed properly.
MACRO 2MACRO 1
LIGHT
:
MODE buttons
Buttons that cannot be programmed.
… 86 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR801 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR801 in the language / languages: English as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info