492661
71
Zoom out
Zoom in
Previous page
1/168
Next page
Advanced Operations
En-71
The HDMI connection in your system is used to deliver
uncompressed digital audio and video information from
one device to the next. There is also additional information
about this digital content that can be delivered. Such
additional information is referred to as “metadata”.
Metadata Compatible mode should be used when there are
home theater components in your system, such as Blu-ray
disc players, set top boxes and displays that use this
additional metadata. For example, Metadata Compatible
mode should be set to ON when there are THX Media
Director™ Enabled devices in the system. This ensures
that this additional information can be received by your
Onkyo AVR and can be sent to other devices that are
connected in your home theater system, with no
interruption.
Digital Processing Crossover Network
Digital Crossover provides a separate routing system by
splitting the audio signal into separate frequency bands
optimized for each speaker driver. It provides a fine, three-
dimensional sound field that extend each driver’s
performance to the uppermost. With its built-in time
alignment function, this system also adjusts the sound
shifting that occurs when there is a physical offset between
sound drivers. At a digital processing level, it corrects this
offset by delaying the related audio signal.
Although this function is meant for speakers without
crossover network, it can also be used with bi-amped
speakers.
Tip
This setting can be done while listening to an audio source.
Press MODE/D (Blue) to switch from the current audio source to
test noises. Pressing MODE/D (Blue) again or the cursor buttons
will stop the test noises and switch back to the original audio
source.
Note
This setting can only be made when “Speakers Type(Front A)
or “Speakers Type(Front B)” is set to “Digital Crossover
( page 66).
Crossover
` 250Hz”, “320Hz”,400Hz”, “500Hz, “630Hz”,
800Hz”, “1000Hz”, “1250Hz”, “1600Hz”,
2000Hz”, “2500Hz”, “3200Hz
”, “4000Hz”,
5000Hz
Output Band for Test
` High + Low
, High, Low:
Select the output for the audio signal.
Tip
Pressing MODE/D (Blue) button plays band-limited test noises
which center on the specified frequency.
We recommend choosing a crossover value that creates no
volume difference between “High” and “Low”.
Note
Refer to your speaker manual when setting without the use of test
noises.
Overlap
` No
` Yes
With this setting, a frequency band near the specified
crossover frequency is output by both tweeters and
woofers. Based on the frequency selected for “Crossover”,
the cutoff frequency of the low-pass filter (LPF) will be set
to 1/3 octave up and that of the high-pass filter (HPF) to
1/3 octave down. Example: With a “Crossover” of
3200Hz”, the cutoff frequency of the woofers’ LPF will
be “4000Hz”, and the tweeters’ HPF will be “2500Hz”.
Tip
Sounds processed by Digital Processing Crossover Network are
played.
You can switch from the current audio source to test noises by
pressing MODE/D (Blue).
In the case of usage of the bi-amped speakers, if there is a
difference between the crossover frequency in the speakers’ built-
in network and the crossover frequency to be set on the AV
receiver, the frequency dip may be caused. Therefore, it is
recommended that this function should be set to Yes”.
High Level, Low Level
` –6.0dB to 0.0dB
to +6.0dB in 0.5 dB steps.
With this setting, you can set the volume of tweeters and
woofers.
Tip
Sounds processed by Digital Processing Crossover Network are
played.
You can switch from the current audio source to test noises by
pressing MODE/D (Blue).
THX Loudness Plus
THX Loudness Plus is a new volume control technology
featured in THX Ultra2 Plus™ and THX Select2 Plus™
Certified receivers. With THX Loudness Plus, home
theater audiences can now experience the rich details in a
surround mix at any volume level. A consequence of
turning the volume below Reference Level is that certain
sound elements can be lost or perceived differently by
the listener. THX Loudness Plus compensates for the
tonal and spatial shifts that occur when the volume is
reduced by intelligently adjusting ambient surround
channel levels and frequency response. This enables
users experience the true impact of soundtracks
regardless of the volume setting. THX Loudness Plus is
automatically applied when listening in any THX
listening mode. The new THX Cinema, THX Music, and
THX Games modes are tailored to apply the proper THX
Loudness Plus settings for each type of content.
Cutoff frequencies of the woofers’ low-pass filter (LPF)
and the tweeters’ high-pass filter (HPF) are set according
to the frequency specified for “Crossover”.
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR3010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR3010 in the language / languages: English as an attachment in your email.

The manual is 4,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR3010

Onkyo TX-NR3010 User Manual - German - 168 pages

Onkyo TX-NR3010 User Manual - Dutch - 168 pages

Onkyo TX-NR3010 User Manual - French - 168 pages

Onkyo TX-NR3010 User Manual - Italian - 168 pages

Onkyo TX-NR3010 User Manual - Swedish - 168 pages

Onkyo TX-NR3010 User Manual - Spanish - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info