492661
67
Zoom out
Zoom in
Previous page
1/168
Next page
Advanced Operations
En-67
Note
•“Speakers Type(Front A)” and “Speakers Type(Front B)
cannot be set to “Bi-Amp” or “Digital Crossover” at the same
time.
Powered Zone 2 cannot be used if “Speakers Type(Front B)” is
enabled.
Powered Zone 3 is not available in the following cases:
–TheSpeakers Type(Front A)” setting is set to “Bi-Amp” or
Digital Crossover”.
–TheSpeakers Type(Front B)” is enabled.
–ThePowered Zone 2” setting is set to “No”.
•When thePowered Zone 3” setting is set to “Yes
( page 66) while Powered Zone 2 is enabled ( page 89),
the surround back speakers cannot be used.
•When thePowered Zone 2” setting is set to “Yes”, the front
wide speakers cannot be used.
•When thePowered Zone 3” setting is set to “Yes”, the front
high speakers cannot be used.
•“11ch Playback” is not available in the following cases:
–TheSpeakers Type(Front A)” setting is set to “Bi-Amp” or
Digital Crossover”.
–TheSpeakers Type(Front B)” is enabled.
–ThePowered Zone 2” setting is set to “Yes”.
–TheZone 2 HDMI” setting is set to “Use”.
If the “11ch Playback” setting is set to “Yes”, the audio of front
wide channel is output from FRONT WIDE PRE OUT only.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
You can set the crossover frequencies, distances, and levels
of the front speakers A and front speakers B independently.
The other speakers (i.e., subwoofer, center, surround,
surround back and front high) use the same crossover
frequencies, distances, and levels for Speakers A and
Speakers B. Specify “Full Band” for speakers that can
output low frequency bass sounds adequately, for example,
speakers with a good sized woofer. For smaller speakers,
specify a crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey MultEQ XT32 Room Correction
and Speaker Setup, please make sure manually that any
THX speakers are set to “80Hz(THX)” crossover.
Subwoofer
` 1ch:
Audio signal is outputted from SW1 jack only.
` 2ch
:
Audio signal is outputted from SW1 and SW2 jacks.
` No
Front
(Setting Speakers A and Speakers B)
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
Note
If the “Subwoofer” setting is set to “No”, the “Front” setting is
fixed at “Full Band”.
If any of “Center”, “Surround”, or “Front High” is set to “Full
Band”, theFront” (Speakers B) setting is fixed to “Full Band”.
Center
*8
, Surround
*8
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
Front Wide
*3*4*6*7*8*9
, Front High
*1*2*3*6
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX),
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
Surround Back
*1*5*6*10
` Full Band
` 40Hz, 45Hz, 50Hz, 55Hz, 60Hz, 70Hz, 80Hz(THX)
,
90Hz, 100Hz, 110Hz, 120Hz, 130Hz, 150Hz, 200Hz
` None
This setting is set automatically by
Audyssey MultEQ
®
XT32 Room Correction and
Speaker Setup function ( page 42). For Speakers B,
you need to change the settings manually.
To be continued
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR3010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR3010 in the language / languages: English as an attachment in your email.

The manual is 4,85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR3010

Onkyo TX-NR3010 User Manual - German - 168 pages

Onkyo TX-NR3010 User Manual - Dutch - 168 pages

Onkyo TX-NR3010 User Manual - French - 168 pages

Onkyo TX-NR3010 User Manual - Italian - 168 pages

Onkyo TX-NR3010 User Manual - Swedish - 168 pages

Onkyo TX-NR3010 User Manual - Spanish - 168 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info