553762
57
Zoom out
Zoom in
Previous page
1/104
Next page
57
En
DTS/DTS-ES/DTS-HD
With this setting, you can specify the listening mode to
be used when a DTS or DTS-HD High Resolution
Audio format digital audio signal is played (DVD, LD,
CD, etc.). Specifies the default listening mode for DTS-
HD Master Audio sources, such as Blu-ray or HD DVD
(input via HDMI).
Other Multich Source
Specifies the default listening mode for multichannel
PCM sources from HDMI IN such as DVD-Audio, and
DSD multichannel sources such as Super Audio CD.
Main menu Miscellaneous
Volume Setup
Volume Display
` Absolute
:
Display range is “Min”, “0.5” through “99.5”,
Max”.
` Relative (THX):
Display range is “QdB”, “–81.5dB” through
+18.0dB”.
With this setting, you can choose how the volume level is
displayed.
The absolute value 82 is equivalent to the relative value
0dB.
Muting Level
`
QdB (fully muted), –50dB to –10dB in 10 dB steps.
This setting determines how much the output is muted
when the muting function is used ( 26).
Maximum Volume
` Off
, 50 to 99 (Absolute display)
` Off
, –32dB to +17dB (Relative display)
With this setting, you can limit the maximum volume.
To disable this setting, select “Off”.
Power On Volume
` Last
, Min, 1 to 99 or Max (Absolute display)
` Last
, QdB, –81dB to +18dB (Relative display)
With this preference, you can specify the volume set-
ting to be used each time the AV receiver is turned
on.
To use the same volume level that was used when the AV
receiver was turned off, select “Last”.
The “Power On Volume” cannot be set higher than the
Maximum Volume” setting.
Headphone Level
` –12dB to 0dB
to +12dB
With this preference, you can specify the headphone vol-
ume relative to the main volume. This is useful if there’s a
volume difference between your speakers and your head-
phones.
OSD Setup
On Screen Display
This preference determines whether operation details
are displayed on-screen when an AV receiver function is
adjusted.
` On
:
Displayed.
` Off:
Not displayed.
Even when “On” is selected, operation details may not be
output if the input source is connected to an HDMI IN.
TV Format (European and Asian models)
For the on-screen setup menus to display properly, you
must specify the TV system used in your area.
` Auto
:
Select this to automatically detect the TV system
from the video input signals.
` NTSC:
Select this if the TV system in your area is NTSC.
` PAL:
Select this if the TV system in your area is PAL.
Language
` English, Deutsch, Français, Español, Italiano,
Nederlands, Svenska, 中文
This setting determines the language used for the on-
screen setup menus.
Main menu Hardware Setup
Remote ID
Remote ID
` 1
, 2, or 3
When several Onkyo components are used in the same
room, their remote ID codes may overlap. To differenti-
ate the AV receiver from the other components, you can
change its remote ID from “1”, to “2” or 3”.
Note
If you do change the AV receiver’s remote ID, be sure to change
the remote controller to the same ID (see below), otherwise, you
won’t be able to control it with the remote controller.
Changing the Remote Controller’s ID
Multi Zone
See “Setting the Multi Zone” ( 75).
Miscellaneous
Hardware Setup
1
While holding down RECEIVER, press and hold
down SETUP until RECEIVER lights (about 3
seconds).
2
Use the number buttons to enter ID 1, 2, or 3.
RECEIVER flashes twice.
57


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-NR1008 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-NR1008 in the language / languages: English as an attachment in your email.

The manual is 4,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-NR1008

Onkyo TX-NR1008 User Manual - German - 204 pages

Onkyo TX-NR1008 User Manual - Dutch - 204 pages

Onkyo TX-NR1008 User Manual - French - 208 pages

Onkyo TX-NR1008 User Manual - Italian - 204 pages

Onkyo TX-NR1008 User Manual - Swedish - 204 pages

Onkyo TX-NR1008 User Manual - Spanish - 208 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info