66920
32
Zoom out
Zoom in
Previous page
1/36
Next page
32
Troubleshooting
If you have any trouble using the receiver, look for a
solution in this section.
Cant turn on the receiver
Make sure that the power cord is plugged into the wall
outlet properly.
Unplug the power cord from the wall outlet, wait 5
seconds or more, then plug it in again.
The STANDBY indicator is ashing
The amp protection circuit has been activated.
Remove the power cord from the wall outlet immedi-
ately. Disconnect all speaker cables and input sources,
and leave the receiver with its power cord discon-
nected for 1 hour. After that, reconnect the power cord
and press the [STANDBY/ON] button again. If you
can not resolve the problem, contact your Onkyo
dealer.
Theres no sound or its very quiet
Make sure the speaker set A or B is on (page 21).
Make sure that all audio connecting plugs are pushed
in all the way (pages 12 - 19).
Make sure that the polarity of the speaker cables is
correct, and that the bare wire is in contact with metal
part of each speaker terminal (page 12).
Make sure that the speaker cables are not shorting.
Make sure that the inputs and outputs of all compo-
nents are connected properly.
Make sure that the correct input source is selected
(page 21).
If the MUTING indicator is shown on the display,
press the remote controllers [MUTING] button to
unmute the receiver (page 22).
If your turntable doesnt have a phono preamp built-
in, you must connect one between it and the receiver.
If your turntable uses an MC cartridge, you must con-
nect an MC head amp, or an MC transformer and a
phono preamp.
Noise can be heard
Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance, so dont do it.
An audio cable may be picking up interference. Try
repositioning your cables.
The tone controls have no effect
If the DIRECT indicator or PURE AUDIO indicator
lights up, the tone controls have no effect. Press the
[DIRECT] button or [PURE AUDIO] button to turn
the function off. The PURE AUDIO indicator will go
off (page 23).
Reception is noisy, stereo FM reception suffers
from hiss, or the FM STEREO indicator doesnt
appear
Relocate your antenna.
Move the receiver away from your TV or computer.
Listen to the station in mono (page 27).
When listening to an AM station, operating the remote
controller may cause noise.
Passing cars and airplanes can cause interference.
Concrete walls weaken radio signals.
If nothing improves the reception, install an outdoor
antenna.
Power
Audio
If you cant resolve the issue yourself, try resetting
the receiver before contacting your Onkyo dealer.
[TX-8522]
To reset the receiver to its factory defaults, turn it
on and, while holding down the [VIDEO] button,
press the [STANDBY/ON] button.
[TX-8222]
To reset the receiver to its factory defaults, turn it
on and, while holding down the [LINE 2] button,
press the [STANDBY/ON] button.
Clear will appear on the display and the receiver
will enter Standby mode.
Note that resetting the receiver will delete your radio
presets and custom settings.
STANDBY/ON
TX-8522
STANDBY/ON
TX-8222
Tuner
TX-85228222_En.book 32 ページ 2006年5月4日 木曜日 午前11時51分
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-8522 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-8522 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-8522

Onkyo TX-8522 User Manual - German - 72 pages

Onkyo TX-8522 User Manual - Dutch - 72 pages

Onkyo TX-8522 User Manual - Dutch, Italian - 72 pages

Onkyo TX-8522 User Manual - Swedish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info