66920
31
Zoom out
Zoom in
Previous page
1/36
Next page
31
Connecting Components not Reached by the Remote
Controller Signals (IR IN/OUT)
In order to use the remote controller to control the
receiver from a remote location, you will need to
prepare a multiroom kit (sold separately) such as one
listed below:
Onkyos Multi-Room System kits (IR Remote
Controller Extension System)
Multiroom A/V distribution and control system such
as those from Niles
®
and Xantech
®
* Xantech is a registered trademark of Xantech Corporation.
* Niles is a registered trademark of Niles Audio Corporation.
Effective Sensor Layout
Example for the main room
If the receiver is located inside a cabinet or other
enclosure where the infrared rays from the remote
controller cannot enter, then operation with the remote
controller will not be possible. In such a case, it will be
necessary to install a remote sensor at a location outside
of the cabinet so that the infrared rays from the controller
can be sensed.
Example for the remote zone
The IR IN input allows you to control the receiver from
the remote zone with the remote controller even though
the remote zone may be on the other side of the building
from the main zone. The diagram below shows how to
make the proper connections for the remote zone.
Making Sensor Connections
When you place the IR receiver in the main room, connect
the cable from the connecting block to the IR IN terminal.
Make the connection as shown below. Do not plug any
equipment into the power outlet until all the connections
are complete.
Effective Sensor Layout
In this situation, you will need to use a commercially
available IR emitter. Connect the mini plug of the IR
emitter to the IR OUT terminal on the receiver and then
place the IR emitter on the remote sensor of the
component or facing it. When the IR emitter is
connected, only the signal input to the IR IN terminal is
output to the IR OUT terminal. The signal input from the
remote sensor on the front of the receiver will not be
output to the IR OUT terminal.
Making Sensor Connections
When you place the IR receiver in the main room, connect
the cable from the connecting block to the IR OUT terminal.
If Remote Controller Signal Does not
Reach the Receiver Remote Sensor
Connecting
block
IR Receiver
Remote controller
IR IN
TX-8522/
TX-8222
In the
cabinet
: Signal ow
Main room
IR Receiver
Remote controller
Connecting
block
Receiver
Main room Remote Zone
: Signal ow
To IR IN
If Remote Controller Signal Does not
Reach Other Components
Receiver
from connecting block
Mini plug cable
IR Receiver
Remote controller
Connecting
block
IR IN
IR OUT
IR Emitter
Receiver
Other
component
: Signal ow
: Signal ow
Other component
Emitter
Remote control
sensor
IR Emitter
Mini plug
Receiver
TX-85228222_En.book 31 ページ 2006年5月4日 木曜日 午前11時51分
31


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Onkyo TX-8522 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Onkyo TX-8522 in the language / languages: English as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Onkyo TX-8522

Onkyo TX-8522 User Manual - German - 72 pages

Onkyo TX-8522 User Manual - Dutch - 72 pages

Onkyo TX-8522 User Manual - Dutch, Italian - 72 pages

Onkyo TX-8522 User Manual - Swedish - 72 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info