492802

One for All URC-8820N Manual

14
Zoom out
Zoom in
Previous page
1/34
Next page
14
Troubleshooting
LED (red light) does not blink when you press a key.
Replace batteries with two new AAA alkaline batteries.
LED (red light) blinks five times after you press a key.
Replace batteries with two new AAA alkaline batteries.
LED blinks when you press a key, but home entertainment
device does not respond.
Make sure the remote control is aimed at your home entertainment
device and is not farther than 15 feet away.
The unit does not control home entertainment devices or
commands are not working properly.
Try all listed codes for the device brands being set up. Make sure
they can be operated with an infrared remote control.
TV/VCR Combo does not respond properly.
Use the VCR codes for your brand. Some combo units may require
both a TV code and a VCR code for full operation.
Changing channels does not work properly.
If the original remote control required pressing ENTER to change
channels, then press ENTER on the remote control after entering
the channel number.
During learning, LED emits a long blink after pressing and
holding key to be learned.
Memory is full or a bad capture has occurred. Avoid high-ambient
light sources, such as direct daylight and fluorescent bulbs. Try
readjusting positions of remote controls before performing the
procedure again.
Tried Searching For Your Code method and still could not
find a working code.
Clear the device key as follows: Press and hold SET until the LED
(red light) blinks twice, then release.Next enter 9 9 2. Then press
the device key to be cleared twice.Now repeat the Searching for
Your Code method.
No remote control of volume.
See “Changing Volume Lock” to lock/unlock volume.
If the above does not work.
Please visit: www.oneforall.com
Consumer Help Line: 1 (800) 315-0990
FCC Compliance
This equipment has been tested and found to comply with the
limits for a class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for One for All URC-8820N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of One for All URC-8820N in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info