492802
13
Zoom out
Zoom in
Previous page
1/34
Next page
13
Using Keymover
This remote includes a Keymover feature that allows you to map (or
copy) keys from one mode (i.e., source mode) to another mode (i.e.,
destination mode).
NOTE: The following keys cannot be used as a source or
destination: TV, CBL/SAT, VCR, DVD, CD, PVR, AUD, AUX, FAV,
and SET.
Programming Keymover
For example, if your VCR does not have volume control, you can
map those keys (i.e., VOL +, VOL -, and MUTE) from the TV mode
to the VCR mode as follows:
1. Press and hold SET until the LED (red light) blinks twice, then
release SET.
2. Enter 9 9 4. The LED will blink twice.
3. For the source mode, press TV once.
4. For the source key, press VOL + once.
5. For the destination mode, press VCR once.
6. For the destination key, press VOL + once.
7. The LED will blink twice, indicating the keymoved sequence is
correct.
8. Repeat steps 1 through 7 twice more to map remaining volume
control keys, substituting VOL - and MUTE as source and
destination keys in steps 4 and 6.
Upon completion of the above procedure, you can now use this
remote to control the TV’s volume and MUTE in the VCR mode, as
well as in the TV mode.
Restoring Keymoved Keys To Default Settings
Restoring a Single Keymoved Key
1. Press a device key that has a keymoved key.
2. Press and hold SET until the LED (red light) blinks twice, then
release SET.
3. Enter 9 9 4. The LED will blink twice.
4. Press the destination key twice (where the keymoved key is
stored). The LED will blink twice.
Restoring All Keymoved Keys in a Single Mode
1. Press and hold SET until the LED (red light) blinks twice.
2. Enter 9 9 4. The LED will blink twice.
3. Press the destination mode twice (where keymoved keys are
stored). The LED will blink twice.
Restoring Factory Default Settings
This remote includes a Setup Code Reset program. You can use it to
restore all your programmed codes to factory settings and delete all
custom programming.
IMPORTANT: Executing this program erases all code settings and all
custom settings including, Macros, Learned Keys, Reassigned Device
Keys, Keymoved Keys, Favorite Channels, and all device settings.
1. On the remote control, press and hold SET until the LED (red
light) blinks twice.
2. Enter 9 8 0. The LED will blink four times.
3. Your remote is now ready for programming.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for One for All URC-8820N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of One for All URC-8820N in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info