713038

Omnitronic BOB series Manual

31
Zoom out
Zoom in
Previous page
1/36
Next page
31
•
EN
5
Operation
BOB-10A subwoofer
1) To prevent loud switching noise, first switch on the connected signal source.
2) Prior to the first switching on of the subwoofer, turn down all level controls to the left stop position to
avoid a high volume at the beginning. Then switch on the subwoofer with the power switch. The POWER
indicator lights up.
3) Adjust the desired volume for the subwoofer with the LEVEL SUB control and for the satellite speakers
with the LEVEL L/R controls. The LIMIT indicator lights up when the signal level is too high. The limiter
will reduce the signal level to protect the speakers. Reduce the volume until the LED does not light
anymore, or only at signal peaks.
4) It is possible to select various equalizer presets with the DSP MODE switch according to your
application: FLAT = frequency response is not affected, LIVE = high frequency attenuation, DJ = low and
high frequency boost, SPEECH = mid and high frequency boost.
5) To switch to mono operation, press the operating mode selector switch. For stereo operation, disengage
the switch.
6) If multiple speakers are operated in parallel, phase displacement between the speakers can lead to
performance and output problems. To compensate this, the phase of each speaker can be switched from
0° up to 180° with the PHASE selector switch.
7) The subwoofer is protected through extensive protective circuits. If a circuit is activated, the red FAULT
indicator lights up. If the indicator lights up during operation or if it does not go out after switching on, the
subwoofer has to be switched off and the cause of the fault has to be removed.
8) After operation, set the LEVEL SUB and LEVEL L/R controls to the left stop position, then switch off the
unit with the power switch. The power indicator goes out.
Setting up a Bluetooth connection with mobile devices
The subwoofer features a Bluetooth receiver allowing you to stream music wirelessly from your mobile
devices such as smartphones, tablets and notebooks.
1) After switching on press the Bluetooth button for 2 seconds until the BT STATUS indicator starts
flashing. The unit will enter the pairing mode.
2) Activate the Bluetooth function at the Bluetooth source and start the device scan. Select “OMNITRONIC“
from the list and connect the devices. Once the devices are paired, the Bluetooth indicator BT STATUS
lights solid.
3) Now play music at the Bluetooth source as you normally would and the sound will come out of the
speaker systems.
4) For decoupling the devices, shortly press the Bluetooth button again.
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Omnitronic BOB series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Omnitronic BOB series in the language / languages: English, German as an attachment in your email.

The manual is 10,68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info