777000
6
Zoom out
Zoom in
Previous page
1/36
Next page
44 45
Usually use this mode with a
camera with communication
capability.
PICTURE SHOOTING USING A DIGITAL CAMERA WITH COMMUNICATION CAPABILITY
<Selecting the control mode>
1. Turn the camera on.
2. Tu rn the electronic flash on. The batteries are recharged
when the Charge lamp lights up.
3. Press the Shutter button of the camera gently to start com-
munication of shooting information including ISO speed,
lens iris and shutter speed between the camera and elec-
tronic flash.
4. Press the MODE button of the electronic flash to select
the flash control mode.
The selected mode is shown in the control panel.
The mode is switched every time the MODE button is
pressed.
Flash control
mode
TTL AUTO
AUTO
MANUAL
FP
TTL AUTO
FP
MANUAL
46
47
49
50 & 52
Control panel
display Control operation Main application Ref.
Pages
Flash is controlled automatically
by performing pre-flash accord-
ing to the camera setup.
Flash light intensity is controlled
according to the light detected
through the auto light receptor of
the flash and to the camera setup.
If the camera has communica-
tion capability, this mode can be
used only when the camera is
an AUTO-compatible model.
Flash is performed according to
the manually set guide number
(GN).
Shooting using manual flash.
TTL AUTO and MANUAL modes
with Super FP emission that can
synchronize with the high-speed
shooting of the single-lens-reflex
focal plane shutter.
Outdoor shooting using flash,
such as sync shooting in the
daytime.
Notes
Certain modes may be unavailable depending on the shooting mode set on the camera and the functions of the
camera in use.
It is not possible to select an unavailable mode.
AT TACHING TO THE CAMERA/REMOVING FROM THE CAMERA
Confirm that both the camera and electronic flash are off.
Attaching or removing the electronic flash while either the flash or the camera is on may result in
malfunction.
How to attach
1. Place the light-emitting section in the standard position
(horizontal, front). If it is in the locked position, press and
turn the Bounce lock release button.
2. Remove the hot shoe cover from the camera.
•Store the hot shoe cover in the pocket located on the inner
side of the flash case.
3. Loosen the lock ring.
If the lock pin is in the out position, press it in by turning it
all the way in the opposite direction to [LOCK] until it
stops.
Lock pin
Electric contact
Do not apply excessive force to the lock pin.
Do not touch the electric contact with a finger or metallic object.
Do not attach the electronic flash while the lock pin is in the out position.
Otherwise, malfunction may result.
4. Slide the electronic flash all the way into the hot shoe until
it stops with a click.
5. Tu rn the lock ring all the way into the direction of [LOCK]
until it stops.
How to remove
1. Loosen the lock ring completely, then slide the electronic
flash out of the hot shoe.
2. Attach the hot shoe cover to the camera.
Notes
To use the electronic flash with a digital camera not equipped with hot shoe:
If the camera has an external flash terminal, the electronic flash can be attached and connected using the flash
bracket and bracket cable (optional).
The electronic flash cannot be used with a camera that is not equipped with a hot shoe or external flash terminal.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olympus FL-50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olympus FL-50 in the language / languages: English as an attachment in your email.

The manual is 9.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info