777000
5
Zoom out
Zoom in
Previous page
1/36
Next page
42 43
1. Press the Power button to turn the electronic flash on.
The control panel lights up and battery charging starts.
2. Ensure that the Charge lamp lights up.
Replace the batteries if the time taken for the Charge lamp
to light up is longer than the values specified below.
Alkaline or Ni-Mn batteries: 30 sec.
Lithium, Ni-Cd or Ni-Mh batteries: 10 sec.
If the Charge lamp and AUTO CHECK lamp blink alter-
nately, it means that the battery capacity is running low. In
this case, replace the batteries.
Memo: To perform test flash activation, press the Test button.
3. Press the Power button again to turn the electronic flash off.
Turn the electronic flash off in the following cases:
• Before mounting it on the camera or dismounting it from
the camera.
When flash emission is not required.
When not using the electronic flash.
LOADING BATTERIES
CR-V3
The batteries are available separately. Always use one of the following battery combinations.
• AA (R6) alkaline batteries (LR6 type) .................................. x 4
• AA (R6) Ni-Cd batteries ....................................................... x 4
• AA (R6) Ni-Mh batteries ....................................................... x 4
• AA (R6) Ni-Mn batteries (ZR6 type) ..................................... x 4
• AA (R6) lithium batteries (FR6 type) .................................... x 4
• Lithium battery packs (CR-V3 type) (Olympus LB-01) ......... x 2
The AA (R6) manganese batteries cannot be used.
How to load the batteries
1. Open the battery compartment cover.
2. Insert the batteries with correct +/– polarity.
3. Close the battery compartment cover.
AA (R6) batteries
The following products (optional) can also be used as an external power supply:
FlashPowerGrip FP-1
FlashHighVoltageSet SHV-1
Notes
• Do not mix old and new batteries or batteries of different types together.
• Remove the batteries when the electronic flash is not going to be used for a long period.
• Carry spare batteries when traveling or when using the flash in cold areas.
CHECKING BATTERIES
After loading the batteries, check the remaining battery capacity by turning the electronic flash on.
Flash Interval and Flash Count
The following table shows the flash intervals and flash counts for various batteries. Data is
based on using batteries all of the same type.
Batteries used Flash interval Flash count
AA (R6) alkaline dry cell batteries (LR6 type) Approx. 6 sec. Approx. 150 times
AA (R6) lithium batteries (FR6 type) Approx. 7 sec. Approx. 170 times
AA (R6) Ni-Mn batteries (ZR6 type) Approx. 5 sec. Approx. 160 times
Lithium battery packs (CR-V3) Approx. 5 sec. Approx. 220 times
AA (R6) Ni-Cd batteries, 1000 mAh Approx. 4 sec. Approx. 110 times
AA (R6) Ni-Mh batteries, 1900 mAh Approx. 4 sec. Approx. 170 times
The flash emission interval and count data were obtained from in-house tests at Olympus.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olympus FL-50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olympus FL-50 in the language / languages: English as an attachment in your email.

The manual is 9.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info