Manual Olsberg ARINA 2.0 (page 80 of 160) (English, German, French)

812264

Zoom out

Zoom in

1/160

Operating manual

for the user

LEVANA 2.0 6 kW

LEVANA 2.0 8 kW

LEVANA AQUA 2.0

ARINA 2.0

INARA 2.0

“SETTINGS” display

convection

frost protection

night set

max. power

n.c.

Fig. 3.17 Touch control panel – General settings

08:00

OKESC

convection

frost protection

night set

max. power

n.c.

7 °C

Fig. 3.18 Touch control panel – Adjust value with arrow buttons

General settings:

By tapping the input eld on the right, the control panel appears

below. The value can be adjusted using the arrow buttons, and then

conrmed with OK. The process can be cancelled with ESC.

Convection

Pellet replace with a nominal heat output of 6 kW:

The convection air blower is an accessory (optional).

Pellet replace with a nominal heat output of 8 kW:

A convection air blower is installed. The pellet replace automat-

ically selects an appropriate blower speed based on the heating

output, which always occurs synchronously with the output stage

and cannot be changed.

Frost protection

The frost protection function is activated when the current room

temperature drops below the frost protection temperature which

is set. The combustion process automatically starts for min. 30

minutes. This also occurs in the “O” operating state (master switch

must be switched on). As soon as the current room temperature

climbs above the frost protection temperature which is set, the

combustion process is ended again and the system switches back

to the previously selected operating mode. The frost protection

temperature can be set to between 5 °C and 10 °C or “---”. Factory

setting: ---

Night time reduction

(Only in “Automatic” mode and with switching times activated.

There is no night time reduction without switching times.)

The night time reduction temperature can be set to between 5 °C

and 20°C or “---”. The factory setting is “---”, i.e. deactivated.

Maximum output

(Only in “Automatic” mode) The max. output stage can be set to

between 1 and 5. Factory setting: 5

Standby (only in “Automatic” mode)

Standby mode can be switched on and o. With standby mode

switched o, the pellet replace continues heating at the lowest

output stage once the preset room temperature is reached. This

means ignition processes are avoided.

In standby mode, the pellet replace switches o when the room

temperature which is set, plus the switch-o hysteresis (1 °C to 3 °C)

is reached.

See also menu: “O temperature settings”.

The temperature at which the pellet replace switches back on

again is set in the “Temperature drop settings” menu. If standby

mode is not desired, then the display must be changed to “O”.

Factory setting: on

Temperature drop (in “Automatic” mode):

The temperature drop describes the switching dierence between

the room temperature which is set and the pellet replace switching

back on in standby mode.

The temperature drop for starting the pellet replace can be set to

between 1 °C and 6 °C. Factory setting: 2 °C

O temperature (in “Automatic” mode only)

The switching hysteresis at which the pellet replace switches to

standby mode is set in the “O temperature” menu. The switch-o

hysteresis can be set to between 1 °C and 3°C. Factory setting: 1 °C

Example:

Room temperature set: .............................................................................20 °C

Temperature drop set: ................................................................................. 2 °C

O temperature set: .................................................................................... 1 °C

The pellet replace switches to standby at: .........20 °C + 1 °C = 21 °C

The pellet replace reignites at: ................................. 20 °C – 2 °C = 18 °C

Follow-up

If an external room thermostat is connected, then the follow-up can

be set to between 1 minutes and 9 minutes or to “---”. As a result, the

pellet replace runs for the time dened in the follow-up once the

preset room temperature has been reached in order to avoid and/or

ignore rapid temperature changes and/or external room thermostat

uctuations (e.g. owing to opening a window for a short time).

Factory setting: ---

We reserve the right to make technical changes

78-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 8078-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 80 11.04.2023 14:41:5811.04.2023 14:41:58

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Olsberg ARINA 2.0 in the language / languages: English, German, French as an attachment in your email.

The manual is 34.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Olsberg ARINA 2.0 Manual

Product: