812264

Olsberg ARINA 2.0 Manual

71
Zoom out
Zoom in
Previous page
1/160
Next page
Installation instructions
for the specialist company
LEVANA 2.0 6 kW
LEVANA 2.0 8 kW
LEVANA AQUA 2.0
ARINA 2.0
INARA 2.0
EN
Olsberg installation unit with return ow increase valve
The return ow increase valve is integrated and permanently set to
55 °C.
12
4
3
Fig. 2.38 Olsberg installation unit
1Flow from pellet replace
2Flow to buer
3Return to pellet replace
4Return from buer
Connection of the pump to the pellet replace
Wire the enclosed 3-pole connector to the pump with L-PE-N (cable
type: H05VV-F 3 x 0.75 mm²) and plug it into the socket.
Fig. 2.39 Connection with a 3-pole connector
Connection of the buer sensor to the pellet replace
Note! Mixing up the buer sensors!
In order to prevent the top and bottom buer sensors from
getting mixed up, the enclosed connectors are coded, i.e. the
connectors only t into the corresponding socket. You can
recognise the same coding by the same colour (pastel blue and
light blue). Install the enclosed top and bottom buer sensors
on the buer.
Attention! Product damage owing to malfunctions!
Swapping the sensors on the buer results in malfunctions.
●Lay the buer sensor cable to the pellet replace, the buer
sensor cable can be extended by max. 15 m if necessary (ca-
ble type: H05VV-F 2 x 0.75 mm² to 2 x 1.5 mm²).
●Wire the top buer sensor with the pastel blue connector
appropriately for the socket and plug it into the socket.
●Wire the bottom buer sensor with the light blue connector
appropriately for the socket and plug it into the socket.
General regulated function
In principle, heating operation of the LEVANA AQUA is regulated
using the “Manual” or “Automatic” operating mode (see “Menu selec-
tion” chapter). I.e., in manual mode the pellet replace heats at
the selected output stage (1-5) until the control temperatures are
reached on the water side.
Note! In automatic mode, the pellet replace heats until either
the room temperature selected or the water-side control
temperatures are reached.
Water-side control function – operation with buer
In Germany, operation without a buer is prohibited by the 1st
BImSchV (Federal Emission Control Act). For pellet replaces, 20 l of
buer volume must be available per kW of water output.
Note! Olsberg also recommends the installation of a buer in
all other distribution countries.
The buer installed is automatically detected by the pellet replace
when it is switched on through querying of the two buer sensors.
Always install both buer sensors for operation with a buer!
During operation with the buer, the pellet replace regulates
according to the “Buer ON” and “Buer OFF” temperatures values,
which can be set individually. The pump only switches on if both of
the following conditions are met:
ū The boiler temperature (water temperature in the pellet replace)
must be greater than 60 °C.
ū The boiler temperature must be 5 °C greater than the dened
“Buer ON” temperature.
The pump switches o if one of the following conditions is met:
ū The boiler temperature must be less than 55 °C.
ū The boiler temperature must be less than the dened “Buer ON”
temperature plus 5 °C.
Note regarding operation without a buer (not permitted
in Germany)!
In the event of operation without a buer, the pellet replace regu-
lates according to the boiler temperature, which is measures in the
pellet replace above the combustion chamber. If the temperature
falls below the boiler temperature of 65 °C, then “Heating operation”
is enabled, and if the temperature falls below 81 °C, then the pellet
replace switches to “Burnout”. The pump switches on at a boiler
temperature of 60 °C and switches o again if the temperature falls
below 55 °C.
We reserve the right to make technical changes
71
78-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 7178-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 71 11.04.2023 14:41:5211.04.2023 14:41:52
… 71 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Olsberg ARINA 2.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Olsberg ARINA 2.0 in the language / languages: English, German, French as an attachment in your email.

The manual is 34.97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info