Manual Olsberg ARINA 2.0 (page 70 of 160) (English, German, French)

812264

Zoom out

Zoom in

1/160

Installation instructions

for the specialist company

LEVANA 2.0 6 kW

LEVANA 2.0 8 kW

LEVANA AQUA 2.0

ARINA 2.0

INARA 2.0

2.8 LEVANA AQUA 2.0 water installation

Water side connection

The water pipes can optionally be laid to the rear (installed in the

factory) or to the bottom through the oor.

For laying through the oor, you must remove the lower rear wall

and adjust the mounting for the ow and return ow accord-

ingly. For laying of the water pipes through the oor, as well as for

removal / installation of the rear cladding, follow a similar procedure

to that which is set out in the “Combustion air nozzles for connec-

tion from the bottom” chapter.

5431 2

Fig. 2.36 Water side connections on the rear of the pellet replace

1Socket for connection of the 3-pole connector for the pump

2Socket (pastel blue) for the top buer sensor connection

3Socket (light blue) for the bottom buer sensor connection

4½” heating return

5½” heating ow

Important information for integration of the pellet re-

place into the heating system and/or domestic cooling

water system:

ū The water connections and the electrical work may only be car-

ried out by expert technicians.

ū We recommend the “Olsberg installation unit” (item no.:

23/5591.9250) for integration into the heating system and/or do-

mestic cooling water system. Observe the separate manual for

this unit here.

ū In addition to the necessary safety components, a return ow in-

crease valve which increases the return ow temperature to at

least 55 °C must always be installed (integrated into the “Olsberg

installation unit”).

ū An outlet tap must be installed in the bottom section of the wa-

ter circuit.

ū A buer must be integrated into the heating system for ecient

and fault-free operation of the LEVANA AQUA 2.0 pellet replace.

As a guideline for the storage volume, approx. 60 litres should be

provided per kW of heating output (approx. 500 litres).

ū For ecient operation of the pellet replace, it is strongly rec-

ommended that both buer sensors (top and bottom) be

connected!

●Clean the heating system before hydraulic connection of the pel-

let replace through ushing in accordance with DIN EN 14336

(Heating systems in buildings – Installation and commissioning

of water based heating systems) so that the function of the pellet

replace is not endangered!

Proof of cleaning must be provided in the event of possible war-

ranty services from Olsberg.

●The pellet replace may never be operated without water.

●The locally applicable regulations and technical rules must also al-

ways be observed!

Venting at the vent valve

●After connection of the ow and return line and lling with wa-

ter, the system should be vented at the vent valve for the pellet

replace.

●Check all water connections on the pellet replace for leaks!

Fig. 2.37 Venting

1Vent valve

We reserve the right to make technical changes

78-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 7078-4643-2481_R6_LEVANA 2.0_ARINA 2.0_INARA 2.0_DE-EN-FR.indd 70 11.04.2023 14:41:5111.04.2023 14:41:51

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Olsberg ARINA 2.0 in the language / languages: English, German, French as an attachment in your email.

The manual is 34.97 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Olsberg ARINA 2.0 Manual

Product: