644159

Oleo-Mac GS200E Manual

31
Zoom out
Zoom in
Previous page
1/202
Next page
27
I
GB
F
D
E
SK
P
GR
TR
CZ
RUS
UK
PL
hand (Fig.11). Chain tension is correct when
it can be lifted approximately 2-4 mm clear
of the guide bar. The chain must be adjusted
so that can be moved freely by hand.
WARNING - The throttle lever must be
pressed before the chain can be rotated.
Check that the power cord is NOT
plugged into the mains socket outlet.
- Fully tighten the chain guard fixing knob
(A, Fig.12) while keeping the tip of the bar
raised.
5. STARTING
OIL FILLING AND CHAIN LUBRICATION
The saw chain is automatically lubricated
during use by a pump which normally requires
no maintenance. The oil flow is pre-regulated
by the manufacturer to ensure a sufficient oil
delivery even under heavy working conditions.
During cutting of thin timber a possible oil
dripping is normal.
- Always wipe off around the filler hole before
unscrewing the cap (A, Fig. 13) so that no dirt
enters the oil reservoir.
- During work watch the oil level (B).
- Add oil whenever the oil level in the reservoir
drops to the notch of the minimum.
- After the filling, operate the motor 2 or 3
times to restore correct oil delivery.
- In case of faults do not try to repair the
machine yourself, but apply to your
authorized dealer.
Correct chain lubrication during the cutting
phase reduces wear to a minimum between the
chain and bar thus prolonging life. Always use a
good quality oil.
WARNING - Never use waste oil.
Always use biodegradable lubrificant
(eco-lube Oleo-Mac p.n. 001001548 (5) -
001001549 (1)) which is specific for bar and
chain and also respectful towards nature,
operator health and electric saw’s parts.
WARNING - Remove the plug for
connection to the mains before carrying
out any operation on the cutting
equipment.
Before starting make sure the chain is
not obstructed.
When the chainsaw is running, grip the
front handle firmly with your left hand
and the back handle with your right hand
(Fig. 14).
- Stop the motor before setting the chain saw
down.
- Do not lean forward and do not cut above
shoulder height; gripping the saw at the top
of the handle makes it difficult to control and
counteract kickback.
- Do not use in trees or on steps, this is
extremely dangerous.
- Ensure that the cable does not snag on
parts of the tree when the machine is in
operation.
- Stop the saw if the chain strikes a foreign
object. Inspect the saw and repair or replace
parts as necessary.
- Left-handers should follow these
instructions too. Keep a proper cutting
stance.
Over exposure to vibrations can result in
blood-vessel or nerve injury to persons
suffering with blood circulation problems.
Seek medical attention if you experience
physical symptoms such numbness, lack
of feeling, reduction in normal strength,
changes in the colour of the skin. These
symptoms normally appear in the fingers,
hands or wrists.
CONNECTION TO THE NETWORK
WARNING - Before connecting the plug
to the network check that the voltage
corresponds to the technical data shown below.
Verify that the dimensions of the extension
cable are according to the specifications,
otherwise a drop in tension may occur causing
a consequent irreparable damage to the motor.
The earth plate is not necessary since the
electric saw motor is double insulated.
… 31 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oleo-Mac GS200E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oleo-Mac GS200E in the language / languages: English, German, French, Italian, Polish, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,74 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oleo-Mac GS200E

Oleo-Mac GS200E User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info