783009
46
Zoom out
Zoom in
Previous page
1/295
Next page
EN 46
Fig.  7 Setting the temperature
1. Press and hold both, the increase + and decrease – buttons of the
control panel at once for more than 3 seconds to toggle between
°C or °F. Please note, that this setting can only be adjusted on the
control panel of the product.
2. Press the increase + / or decrease – / button separately to
select a temperature between 17 °C to 30 °C or 62 °F to 88 °F.
Fig.  8 Setting the fan speed
Press the fan speed button FAN to toggle between the speed settings.
The respective indicator on the control panel and the remote control
show the current setting.
Note:
There is no indicator at the control panel for the auto speed setting.
Fig.  9 Louvre adjustment
The louvres of the air outlet can be adjusted manually in any mode to fit
required needs.
Fig.
10
Setting the timer
The timer switches the product on or into standby when a user-defined
time has elapsed. When switching on, the last mode and setting will be
used. The set durations will be counted down immediately. Please note,
that this setting can only be activated with the remote control of the
product.
1. Press the specific TIMER ON/OFF button at the remote control to
enter the timer setting for either the auto-on or auto-standby timer.
The respective indicator for each setting will light up.
2. Press the specific TIMER ON/OFF button at the remote control as
often as necessary to set a time from 0.5 to 24 hours.
3. The setting will be saved after 5 seconds without input.
Examples:
To have the product switch itself o after 1 hour and on again after
another 1-1/2 hours, set the auto-o time to 1.0 h and the auto-on time to
2.5 h during operation.
To have the product switched on after 8 hours and o after another 8
hours, set the auto-on time to 8.0 h and the auto-o time to 16.0 h while
in standby.
Notes:
• The adjusting increments are 0.5 hours up to 10 hours, then 1 hour up to
24 hours.
• The respective indicator will be lit, when a time is set.
• Switching the product on or into standby manually will cancel the timer
setting.
• The timer settings will be lost once the respective actions were
conducted and the time needs to be set again.
• The timer setting will be lost in case an error occurs (see protection
and error codes).
IM_OAC7020W_OAC7020B_200110_V06_HR.indb 46 10/1/2020 14:15
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for OK OAC 7020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of OK OAC 7020 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish as an attachment in your email.

The manual is 16.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info