551838
60
Zoom out
Zoom in
Previous page
1/68
Next page
60
OC1 OPERATING MANUAL
© 2002 Design, 2009 Doc. No. 12-2761-r04 (9/6/11)
Inspection
• Closely check all of the sealing surfaces for any signs of damage that might impair proper sealing.
• Inspect the Buttons, Lens, and Housing to ensure they are not cracked or damaged.
WARNING: If damage or corrosion is found, return your OC1 to an Authorized Oceanic Dealer, and
DO NOT attempt to use it until it has received factory prescribed service.
• Remove the case back O-ring (Fig. 164a) by squeezing the sides. Discard, and do not attempt to reuse it.
> It is located around the top rim of the battery case back.
> DO NOT use tools to remove the O-ring.
> To ensure proper sealing, O-ring replacement is required each time the Battery is replaced.
OC1 Battery Installation
• Very lightly lubricate the new O-ring with silicone grease and place it on the top rim of the battery cover.
• Place a new 3 volt type CR2450 Lithium Battery, negative side down into the Battery cavity and ensure that it is evenly
positioned (Fig. 165).
• Carefully align the front and back sections of the case, inserting the guide pin (Fig. 166a) in the guide hole.
• While ensuring that the front and back of the case or properly aligned, firmly press them evenly and completely together
(Fig. 167).
• While holding the sections firmly together, insert the (4) retaining screws and tighten them until secure by turning them
clockwise with a small flat tip 3mm screw driver.
Testing
> Ensure that the LCD is clear and sharp in contrast. If any portions are missing or appear dim, or if a Low Battery condition is
indicated, return the OC1 with TMTs to an Authorized Oceanic Dealer for evaluation before use.
> During 24 hours after completion of a dive, the graphic DATA with selections SAVE ? and CLEAR ? will be displayed (Fig.
168) giving you the option to retain or delete Ni-O2 calculations for repetitive dives.
• A (< 2 sec) to toggle between SAVE and CLEAR
• S (< 2 sec) to save the selection
> Graphics DATA SAVED (or CLEARED) with CAL COMPASS appear for 3 seconds (Fig. 169), then operation reverts to the
Compass CAL screen.
> Calibrate the Compass. Refer to page 54.
> Verify all Set Points prior to diving.
• Pressurize the Regulator Assembly (and Transmitter).
• Verify that the Link icon is displayed.
• Check the TMT Status screens. Refer to page 25.
Fig. 164 - BATT O-RING
Fig. 165 - BATT INSTALLED
a
Fig. 166 - ALIGNMENT OF
FRONT/BACK
a
Fig. 167 - PRESS FRONT
AND BACK TOGETHER
Fig. 168 - SELECT
Fig. 169 - DATA SAVED
60


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oceanic OC1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oceanic OC1 in the language / languages: English as an attachment in your email.

The manual is 8,03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oceanic OC1

Oceanic OC1 User Manual - English - 180 pages

Oceanic OC1 Additional guide - German - 2 pages

Oceanic OC1 Quick start guide - German - 2 pages

Oceanic OC1 User Manual - German - 68 pages

Oceanic OC1 Additional guide - French - 2 pages

Oceanic OC1 Quick start guide - French - 2 pages

Oceanic OC1 User Manual - French - 68 pages

Oceanic OC1 Additional guide - Italian - 2 pages

Oceanic OC1 User Manual - Italian - 68 pages

Oceanic OC1 User Manual - Turkish - 180 pages

Oceanic OC1 User Manual - Spanish - 68 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info