Manual Oceanic OC1 (page 59 of 68) (English)

551838

Zoom out

Zoom in

1/68

OC1 OPERATING MANUAL

CARE AND CLEANING

Protect your OC1 from shock, excessive temperatures, exposure to chemicals, and tampering. Protect the lens against scratches

with a Instrument Lens Protector. Small scratches will naturally disappear underwater.

• Soak and rinse the OC1 in fresh water at the end of each day of diving, and check to ensure that the areas around the

Low Pressure (Depth) Sensor (Fig. 160a), PC Interface Data Port (Fig. 160b), and Buttons are free of debris or obstructions.

Soak and rinse the Regulator with the Transmitter attached.

• To dissolve salt crystals, use lukewarm water or a slightly acidic bath (50% white vinegar/50% fresh water). After removal

from the bath, place the OC1 and the Regulator with Transmitter under gently running water and towel dry before storing.

• Transport your OC1 system cool, dry, and protected.

INSPECTIONS AND SERVICE

Your OC1 should be inspected annually by an Authorized Oceanic Dealer who will perform a factory prescribed function check

and inspection for damage or wear. To keep the 2 year limited warranty in effect, this inspection must be completed one year

after purchase (+/- 30 days).

Oceanic recommends that you continue to have an inspection performed every year to ensure it is working properly. The costs of

annual inspections, or inspections relating to water tight integrity, are not covered under the terms of the 2 year limited warranty.

To Obtain Service:

Take your OC1 system to an Authorized Oceanic Dealer or send it to the nearest Oceanic Regional Facility (page xx).

To return your OC1 system to Oceanic:

• Record all dive data in the Log and/or download the data stored in memory. All data will be erased during factory service.

• Package it using a protective cushioning material.

• Include a legible note stating the speciﬁc reason for return, your name, address, daytime phone number, serial number(s),

and a copy of your original sales receipt and Warranty Registration Card.

• Send freight prepaid and insured using a traceable method to the nearest Oceanic Regional Service Facility, or to Oceanic

USA.

• If shipping to Oceanic USA, obtain an RA (Return Authorization) number by contacting Oceanic at 510/562-0500 or send

an e-mail to service@oceanicusa.com.

• Non-warranty service must be prepaid. COD is not accepted.

• Additional information is available at the Oceanic web site OceanicWorldwide.com

BATTERY REPLACEMENT

CAUTION: The procedures that follow must be closely adhered to avoid entrance of water into the

unit. Damage due to improper Battery replacement (or subsequent leakage of moisture into the unit)

is not covered by the OC1's 2 year warranty.

NOTE: The OC1 can be sent to Oceanic Worldwide, Regional Distributor, or Authorized Dealer Service

for proper battery change service which includes pressure (depth) and leak testing to the max operat-

ing depth. Standard charges for service will apply

The Battery Compartment(s) should only be opened in a dry and clean environment with extreme care taken to prevent the

entrance of moisture or dust.

As an additional precautionary measure to prevent formation of moisture in the Battery Compartment(s), it is recommended that

the Battery(s) be changed in an environment equivalent to the local outdoor temperature and humidity (e.g., do not change the

Battery(s) in an air conditioned environment then take it outside during a hot sunny day).

Inspect the Buttons, Lens, and Housing(s) to ensure they are not cracked or damaged. If there is any sign of moisture in the OC1

or Transmitter(s), DO NOT attempt to use the OC1 for diving (NORM, GAUG, or FREE) until it receives proper service by the

Oceanic factory or an Authorized Regional Distributor.

Data Retention

When the OC1 battery is removed, settings and nitrogen/oxygen calculations for repetitive dives will be retained in volatile

memory until a new battery is installed. You will have the choice of saving or deleting the data (refer to page 60). The Compass

will need to be calibrated after the new battery is installed (refer to page 54).

All parts needed for the battery change that follows are provided in the OC1 Battery Kit available at your Authorized Oceanic

Dealer as Oceanic PN 04.6175.35.

OC1 Battery Removal

• There is no need to remove the straps.

• Remove the (4) retaining screws located on the back of the watch case (Fig. 161) by turning them counter clockwise with a

small ﬂat tip 3mm screw driver.

• Carefully separate the front and back sections (Fig. 162). The Battery may fall out. DO NOT pry apart with tools.

• Turn the case to one side to drop the Battery into your hand. If necessary, gently loosen it with the tip of your ﬁnger. DO

NOT use tools to pry it out, or short the positive (+) top of the Battery (Fig. 163a) to the negative ( - ) contact under it.

• Discard the Battery according to local regulations governing disposal of Lithium batteries.

Fig. 160 - OC1 FRONT

Fig. 161 - CASE BACK

Fig. 162 - SEPARATE FRONT

AND BACK

Fig. 163 - BATT INSTALLED

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Oceanic OC1 in the language / languages: English as an attachment in your email.

The manual is 8,03 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Oceanic OC1

Oceanic OC1 User Manual - English - 180 pages

Oceanic OC1 Additional guide - German - 2 pages

Oceanic OC1 Quick start guide - German - 2 pages

Oceanic OC1 User Manual - German - 68 pages

Oceanic OC1 Additional guide - French - 2 pages

Oceanic OC1 Quick start guide - French - 2 pages

Oceanic OC1 User Manual - French - 68 pages

Oceanic OC1 Additional guide - Italian - 2 pages

Oceanic OC1 User Manual - Italian - 68 pages

Oceanic OC1 User Manual - Turkish - 180 pages

Oceanic OC1 User Manual - Spanish - 68 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Oceanic OC1 Manual

Product: