550341

Oceanic DIN USA Converter Manual

6
Zoom out
Zoom in
Previous page
1/12
Next page
6
O2 Tech Reg
REMOVAL OF HOSES
WARNING: At least one Second Stage must be connected to
the First Stage to facilitate purging of breathing gas from
the First Stage.
To remove a Hose from the First Stage -
• Ensure that the Regulator System is purged of all breathing gas.
• Loosen and remove the Hose by turning it in the counter clockwise direction
with an open end wrench of the appropriate size.
REGULATOR ATTACHMENT TO A TANK
WARNING: Maximum working pressure for an Oceanic DIN
style connector is 4500 psi / 300 BAR
DIN STYLE CONNECTOR
Before attaching the Regulator to the Tank:
• Slowly open then close the Tank's Valve to allow a momentary flow of
breathing gas to blow any moisture or contaminants from the breathing gas
opening in the Tank Valve.
• Examine the Threads in the Valve to ensure they are clean and free of burrs
or defects that could damage the Threads of your Regulator DIN Fitting.
To attach the Regulator to the Tank:
• Remove the Protector Cap from the Threads of the Regulator DIN Connec-
tor, and examine the Threads and sealing O-ring. Replace the O-ring if it is
damaged.
• Using care not to cross the Threads, thread the DIN Connector clockwise
into the Cavity of the Tank Valve until it is secure.
• Slowly open the Tank Valve (with the Pressure Instrument facing away from
you) and listen to ensure there is no leakage from the Regulator/Tank Con-
nection.
• If any leakage is observed, repeat the attachment procedure and inspect the
sealing O-ring. If air still leaks, DO NOT USE! Take the Regulator and
Tank to an Authorized Oceanic Dealer for inspection and service.
To remove the Regulator from the Tank:
• Close the Tank Valve and purge all pressure from the Regulator System by
depressing the Purge Button of the Second Stage Regulator.
• Turn the DIN Connector Wheel counter clockwise out of Cavity in the Tank
Valve.
• Place the Protector Cap on the Threads of the DIN Connector.
• Prevent water from entering the First Stage. DO NOT blow breathing
gas near a First Stage that does not have the Protector Cap in
place.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oceanic DIN USA Converter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oceanic DIN USA Converter in the language / languages: English as an attachment in your email.

The manual is 0,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info