550341

Oceanic DIN USA Converter Manual

5
Zoom out
Zoom in
Previous page
1/12
Next page
5
Owner's Guide
O24 FIRST STAGE
WARNING: Failure to prepare your First Stage properly for
use in harsh environmental conditions, such as being
subjected to sediment or the possible buildup of ice, or salt
crystals, may result in serious injury or death.
Operation of your First Stage is not visible when using a regulator system. The
First Stage converts the cylinder's high pressure breathing gas to an intermediate
pressure of approximately 140 psi that can be handled by the regulator Second
Stage to deliver a smooth flow of breathing gas upon demand (i.e., when you
inhale). Intermediate pressure gas is also available for inflation of a BC or dry
suit.
WARNING: Under no circumstances should adjustment of
an Oceanic regulator First Stage be performed by anyone
other than an Authorized Oceanic Service Technician. Doing
so may cause failure underwater, resulting in serious injury
or death.
ATTACHMENT OF HOSES
Low Pressure (LP) and High Pressure (HP) Port Thread sizes are different, making
incorrect installation of Hoses unlikely. However, to avoid damage or personal
injury that may occur due to incorrect installation, Oceanic strongly recommends
having installation performed professionally by an Authorized Oceanic Dealer. If
this is not possible, proceed as follows.
Type of Hose Being Connected:
• Determine whether the Hose that you are installing requires connection to
an HP Port (for a Pressure Gauge or Air Integrated Computer), or to an LP
Port (for an Octopus Second Stage, or a BC or Dry Suit Inflator).
• Be sure that you only place high pressure accessory Hoses in Ports specifi-
cally marked with the letters 'HP', or '4500 psi / 300 BAR'.
Installing Hoses:
After having determined the type of Hose -
• Remove the Port Plugs from those Ports to be used by turning them counter
clockwise with a 5/32" hex key. Save for possible future use.
• Lightly lubricate the Hose-End Threads and O-ring with Christo-Lube
MCG111 Lubricant.
• Thread the Hose clockwise into the Port until secure, then tighten it with an
open end wrench of the appropriate size to a torque of 40 in-lbs.
• • Second Stage - 9/16" wrench
• • LP Inflator - 9/16" (or 1/2") wrench
• • HP Gauge or Integrated Computer - 5/8" wrench
• After all Hoses are connected, test the complete Regulator Assembly by at-
taching it to an appropriate Tank, pressurizing the system, and carefully lis-
tening for leakage of breathing gas.
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oceanic DIN USA Converter at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oceanic DIN USA Converter in the language / languages: English as an attachment in your email.

The manual is 0,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info