47662

Oce PP16C Operation Guide Manual

206
Zoom out
Zoom in
Previous page
1/218
Next page
B.5 RS-232C Cable Connection
B-9
B.5 RS-232C Cable Connection
B.5.1 Preparing an RS-232C Cable
After you procure an RS-232C cable, check its wiring against the pin assignments shown in
page section B.1.2 Interface Signals on page B-3. If you have an IBM communications
adapter cable type 1502067, use the procedure below to solder the wiring at the end (printer
side) of the cable:
1
Unscrew the plastic cover at the end (printer side) of the cable.
2
A bare shield wire is provided for each wire in the cable. Solder all shield wires
together into a single bundle.
3
Connect the bundled shield wires to the connector metal face using a piece of flat
cable about 3 mm wide and 15 mm long,. Make sure that the soldered connections
are secure.
4
Unsolder wires 2 and 3, then resolder them in a crossover configuration. In other
words, solder wire 2 to pin 3 and wire 3 to pin 2. Cover the solder joints with a
thermofit tube.
5
Cut wires 4, 5, 6, and 20.
6
Solder wires 5 and 6 together and connect them to pin 20. Cover the solder joints
with a thermofit tube. Leave wire 4 unconnected.
7
Tape all remaining loose ends together, or seal them with a thermofit tube.
8
Screw the plastic cover back on the cable end.
B.5.2 Connecting the Printer to the Computer
Make sure that both computer and printer are powered off.
1
Discharge static electricity from your body by touching a metal object such as a
doorknob.
2
Plug the end (printer side) of the RS-232C cable into the printer’s serial interface
connector and screw it on securely.
3
Plug the other end of the cable into the computer’s serial interface connector.
4
Power on the printer.
5
The printer’s parameters are set at the factory as follows:
Baud rate = 9600 bps, data bits (character length) = 8, stop bits = 1, parity = none
The two RS-232C protocols are XON/XOFF and DTR. The printer executes both of
these protocols simultaneously, using positive logic for DTR.
… 206 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce PP16C Operation Guide at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce PP16C Operation Guide in the language / languages: English as an attachment in your email.

The manual is 3,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info