47575

Oce OP40 Operation Guide Printing System Functions Manual

85
Zoom out
Zoom in
Previous page
1/102
Next page
2-9
2. Windows KX Driver
■ Staple
Stapling is possible if the optional finisher is installed.
* Stapling is only available with 20 ppm copiers.
* The following settings are required before stapling is possible:
(1) “Device Options” setting in the “Device Settings” Tab
• Select [RAM Disk] or [Hard Disk].
• Select [Internal Finisher], [Finisher] or [Booklet Stitcher].
(2) “Output” Tab
• When the Internal Finisher is installed, select [Finishing Tray] as the “Output to” setting.
• When the Finisher is installed, select [Main Tray] as the “Output to” setting.
• When the Booklet Stitcher is installed, select [Finisher Tray (Face-Down)] as the “Output to” setting.
• Put a check mark in the checkbox for [Collate].
• Put a check mark in the checkbox for [Staple] and select the desired type of stapling you want performed.
Upper Left Upper Right Booklet Booklet Stitch
Notes
•“Booklet” and “Booklet Stitch” cannot be selected when the Internal Finisher is installed. “Upper Left” or “Upper Right” should be selected
according to the orientation of the paper set in the cassette. If either “Upper Left” or “Upper Right” is selected, a message will be
displayed in order to verify the orientation of the paper.
•“Booklet Sticher” cannot be selected when the Finisher is installed.
• In order to staple in the lower left or lower right of the paper, select “Rotated” as the “Orientation” setting in the “Media” Tab.
■ Punch
When the optional Finisher is equipped with a Punch Unit, it is possible to have holes punched into the finished copies.
* In order to use the Hole Punch function, it is first necessary to perform the following settings.
(1) “Installable Options” setting in the “Device Settings” Tab
Select [Finisher] or [Booklet Stitcher] and select the type of Punch Unit. For more details on how to select the Punch Unit, refer to
“Punch Unit” on page 2-15.
(2) In the “Output” Tab
• When the Finisher is installed, select [Main Tray] or [Sub Tray] as the “Output to” setting.
• When the Booklet Stitcher is installed, select [Finisher Tray (Face-Down)] as the “Output to” setting.
• Put a check mark in the checkbox for [Punch] and select the type of hole punching you want performed.
■ Mailbox
When the optional Mailbox Unit is installed, the copies can be ejected into the specified Mailbox Tray.
* In order to use the Mailbox Unit, it is first necessary to perform the following settings.
(1) “Installable Options” setting in the “Device Settings” Tab
Select [Finisher] and then [Mailbox].
(2) In the “Output” Tab
• Select [Mailbox (Face-Down)] or [Finisher Tray (Face-Up)] as the “Output to” setting.
• Put a check mark in the checkbox for [Mailbox] and select the desired tray.
Note
The Hole Punch and Staple functions cannot be used when the copies are to be ejected into the Mailbox.
■ Job Settings...
Clicking on the [Job Settings...] button opens up the [Job Settings] dialog box from which you can print out using the e-MPS (Job Storage)
function. For details, see “2-6-1 Printing using the e-MPS function” on page 2-10.
… 85 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce OP40 Operation Guide Printing System Functions at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce OP40 Operation Guide Printing System Functions in the language / languages: English as an attachment in your email.

The manual is 6,58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info