47327
17
Zoom out
Zoom in
Previous page
1/25
Next page
16
COMMAND CENTER
6-2 Advanced > Protocols: TCP/IP: IP Filters
IP filters specify a host or network of hosts that are allowed to access the printing
system. An entry should be a network number or host IP address. Up to 16 access list
entries are allowed.
When there are no entries, access is allowed to all hosts. To allow all hosts on network
192, enter 192.0.0.0 and 255.0.0.0. To allow only a host 192.168.1.2, enter 192.168.1.2.
The default mask 255.255.255.255 is assumed and subnet mask can be left blank.
Insert a check mark for the protocol that you want to select.
6-3 Advanced > Protocols: TCP/IP: Logical Printers
Logical Printers allows you to use this machine as 4 virtual printers, each with
customized features such as ASCII to Postscript conversion, and the addition and/or
replacement of character strings (commands) at the beginning or end of job data.
Each logical printer can be used with either FTP, LPR, or IPP protocols. All printout to a
non-existent port will be accomplished to Logical Printer1.
Note
For details on available commands, refer to the instruction manual for your workstation.
Item Description
TCP/IP Port Number Specifies the IP address for the logical printer as well as the TCP raw port
number (9100, etc.). Conversion is applied to data that is input to the
specified raw port in accordance with the designated logical printer. This
port is invalid if it is given a port number that is the same as that of an
already specified port (e.g. FTP or LPD).
Bi-directional Printing Enables (On) or disables (Off) bi-directional printing using the TCP/IP raw
port.
If you turn this setting Off, all data received from the printer will be ignored.
In order to have the data that is received from the printer returned to the
client when printing with PostScript, PJL and other such commands, it is
necessary to enable bi-directional printing.
Start of Job String Specifies the character string sent to the printer before output directly to
the output port (lp port).Specifies the character string if it is necessary to
transmit the control code before printing.
End of Job String Specifies the character string sent to the printer after directly outputting to
the output port (lp port). Specify a character string, if it is necessary, to
send a control code after printing.
Banner Page Enables (On) or disables (Off) output of a banner page with printing with
FTP or LPD.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Oce OP1016 Operation Guide Command Center at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Oce OP1016 Operation Guide Command Center in the language / languages: English as an attachment in your email.

The manual is 1,69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info